Window Felt and Run Channel Set
p/n: 70-2485-58
This eight (8) piece Window Felt and Run Channel Set includes the window felt beltline weatherstrips and flex run channels needed for the side window glass. This Original style materials set does two (2) front doors.
Front Door Weatherstrip Set
p/n: 90-0124-72
This Front Door Weatherstrip Set is the primary weatherstrip for the door to the body. Set includes the door bottom and perimeter weatherstrips that attach to the body and the door edge weatherstrip that attaches to the door.
Front Door Vent Window Weatherstrip Set
p/n: 60-0065-55
This four (4) piece Front Door Vent Window Weatherstrip Set contains the main vent window weatherstrips and division post weatherstrips. All of the pieces were designed from original parts for a precise, factory like fit.
Windshield Gasket
p/n: 60-0169-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Windshield Gasket
p/n: 60-0083-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Windshield Gasket
p/n: 70-1945-50
This Windshield Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Body Bumper Kit
p/n: 90-0213-90
This sixteen (16) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
Door Edge Weatherstrips
p/n: 60-0030-73
This Door Edge Weatherstrip pair is designed from the original part for superior fitment and sealing. These primary door weatherstrips mount directly to the vehicle body.
Steering Gear Grommet
p/n: 60-0436-32
This Steering Gear Grommet is designed from the original part for superior fitment and function. Molded with metal core as original with all original features.
Rigid Run Channels
p/n: 60-0073-58
This Rigid Run Channel pair is un-beaded, cloth covered, and mohair lined. Helps eliminate window rattles and provides a smooth sliding surface for glass movement. Also works to protect the glass.
Axle Bumpers
p/n: 60-0491-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming rebound pads are dense rubber blocks that mount to the rear axle tube.
Rear Quarter Window Gasket Set
p/n: 60-0092-83
This rear corner quarter window gasket set contains the quarter window gaskets and locking strips. All of the strips in this four (4) piece set come in forty-five inch (45") pieces and mount around the perimeters of the quarter windows on five window trucks. The ends may require trimming and bonding for installation.
Running Board To Body Filler
p/n: 70-1116-45
This Running Board To Body Filler is extruded from dense rubber for a durable and proper seal. Sold as a forty (40") inch pair of filler strips.
Rear Window Gasket Set
p/n: 60-0082-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Window Felt Beltline Weatherstrips
p/n: 80-0055-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This four (4) piece set includes inner and outer window felt beltline weatherstrips for each door side window.
Parking Brake Boot
p/n: 60-0145-24
This Parking Brake Boot is used for the brake lever at the floor. Designed from an original part and molded from EPDM dense rubber for durability and proper fit.
Overload Spring Arm Bumpers
p/n: 70-2301-32
A reproduction Overload Spring Arm Bumper pair manufactured to OEM specifications. Fully molded quality rubber bumpers that installs in the truck's overload spring arms.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Vent Window Division Post Weatherstrips
p/n: 60-0663-56
This Vent Window Division Post / Bar Weatherstrip pair is fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Accelerator Pedal Pad
p/n: 60-0301-41
This Accelerator Pedal Pad is designed from the original part for superior fitment and function. The accelerator pedal pad is designed to slipover a metal pedal core. Exact copy.
Flexible Run Channel - 5ft.
p/n: 70-1107-57
A cloth covered and mohair-lined type Flexible Run Channel. For sides and top of side windows. Available in 5- foot lengths.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Cowl Vent Gasket
p/n: 60-0124-54
Gasket, cowl vent. Original labyrinth style, not sponge.Length: 16.5 inches. Width: 4.0 inches.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Door Weatherstrip
p/n: 60-0313-73
Weatherstrip, door bottom. Retained by metal strip, black only. Each strip approximately thirty two and one half (32-1/2) inches long.
Hood to Cowl Weatherstrip
p/n: 60-0138-42
This Hood To Cowl Weatherstrip pair installs at the rear of the engine bay to seal between the hood and vehicle body cowl. Sold as a pair for left and right side.
Beltline Rubber Scraper Weatherstrip
p/n: 60-0287-58
This Beltline Rubber Scraper Weatherstrip pair is designed from the original part for an authentic fit, finish, and appearance. Fits at the door outer window at beltline. Each strip approximately is twenty-six (26) inches to twenty-seven (27) inches long.
Fuel Filler Neck Grommet
p/n: 60-0271-41
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fully molded rubber grommet in a slightly oblong shape.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Clutch and Brake Pedal Pads
p/n: 60-0218-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Bumpers
p/n: 60-0579-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. This pedal to floorboard bumper is the longer type with one and three-eighths (1-3/8") inch clearance for the pedal shaft.
Door Weatherstrips - Lower
p/n: 60-0078-73
This Lower Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Heavy type with original ribbing and retainer lip.
Hood Bumper Set
p/n: 33-0680-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Cowl Vent Drain Hose
p/n: 60-0381-54
This Cowl Vent Drain Hose is designed from the original part for superior fitment and seal. Length: 7-1/4" inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
1-11/16" Firewall Grommet
p/n: 60-0057-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from original parts for excellent workmanship.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Steering Column Gasket
p/n: 60-0435-32
This Steering Column Gasket is designed from the original part for superior fitment and sealing. Gasket is die cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Wiring Grommet
p/n: 70-0355-14
This Wiring Grommet is used to run electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fully molded from top-quality EPDM dense rubber to provide excellent durability.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Hood Side Upper Bumper
p/n: 70-2617-42
This Hood Side Upper Bumper is fully molded with top quality EPDM rubber. The authentic configuration for 1/4" hole. Six (6) bumpers typically required per vehicle.
Rear Spring Shackle Rubber Bushing
p/n: 60-0236-48
This Rear Spring Shackle Rubber Bushing is designed from the original part for an authentic fit, finish and function. Bushing fits left or right-hand side and upper or lower spring eye.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
5/8" Door Weatherstrip
p/n: 70-0219-73
The Door Weatherstrip is designed for 1941-1957 GM, Mopar and Packard vehicles but with its generic shape it has many uses outside of its original purpose. Available by the foot.
Shock Absorber Grommet
p/n: 60-0235-33
This Shock Absorber Grommet is fully molded and designed from the original part for superior fitment and durability. The grommet the plain cylinder type with flat ends for shock absorber mounting.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Flexible Run Channel Retainer Clip
p/n: 60-0451-58
A tempered spring steel. Retainer Clip for flexible run channel. For sides and top of side window.
Run Channel Retaining Clip
p/n: 60-0374-58
This Run Channel Retaining Clip is designed from the original part for an authentic fit, finish and function. Clip fits at the end of door window run channel. Tempered spring steel.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Taillight Lens Gaskets
p/n: 70-3770-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
15/16" Firewall Grommet
p/n: 32-0162-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for firewall applications such as ignition to starter wire through the firewall.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
Peel-N-Stick Door Weatherstrip
p/n: 70-0145-WT
This Peel-N-Stick Door Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
11/16" Door Weatherstrip
p/n: 70-0145-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
3/4" Parking Brake Grommet
p/n: 32-0537-24
This Parking Brake Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the parking brake release rod.
3/4" Hood and Door Bumper
p/n: 33-0459-42
This Hood and Door Bumper is fully molded and designed from the original part for superior fitment and seal. Designed for hood to cowl and door hinge pillar upper bumper. May be used in both places.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
5/16" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.
Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.