Door Check Strap
p/n: 40-0535-70
Strap, door check. T-type, special heavy duty construction of rubber with multiple ply webbing and molded-in steel crossbar. Full length as original with one eighth (1/8) inch by seven eighths (7/8) inch steel crossbar.
Rear Bumper Grommet
p/n: 40-0112-30
Grommets, rear bumper symmetrical, right and left. Perfect detailing on both inner and outer surfaces. Fully molded rubber.
Windshield Filler
p/n: 40-0266-52
Bumpers, windshield frame to pillar. Closed bodies with split windshield. 2 rights and 2 lefts required per car. Four (4) piece set.Length: 2.25 inches.
Brown Handbrake Floorplate
p/n: 40-0110-89
Floorplate, handbrake. Brown rubber. Steel core as original.
Handbrake Floorplate
p/n: 40-0110-24
Floorplate, handbrake. Black rubber. For brown see our #40-0110-89. Brass core as original.Length: 6.6875 inches.
Swing-Out Windshield Weatherstrip
p/n: 40-0033-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11') foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Spare Wheel Carrier Grommet
p/n: 40-0254-37
Grommet, rear spare wheel carrier bracket hole. Two (2) per car.Length: 4.1875 inches.
Rear Spare Wheel Carrier Seal
p/n: 40-0141-37
Grommet, rear spare wheel carrier.Some models require 3 pieces (1-1/2 prs).Length: 3.375 inches.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Carpet Heel Plate
p/n: 40-0087-88
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Fender Skirt Edge Weatherstrip
p/n: 40-0279-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Brown Gearshift Boot
p/n: 40-0111-89
Boot, base of gearshift lever. Brown rubber. For black see our #40-0111-88. Made separately to fit most of our gearshift floorplates. Copied from original.
Fuel Neck Grommet
p/n: 40-0099-39
Grommet, fuel filler neck. Fully molded rubber. Four and five sixteenths inch (4-5/16") outside diameter by two and three sixteenths (2-3/16") inside diameter by three eighths inch (3/8") height.
Side Mount Clamp Cushion
p/n: 40-0138-37
Cushion, sidemount clamp. Two and one eighth (2-1/8) inch by four and five eighths (4-5/8) inch.Length: 4.625 inches. Width: 2.125 inches.
Gearshift Boot
p/n: 40-0111-88
Boot, base of gearshift lever. Black rubber. For brown see our #40-0111-89. Made separately to fit most of our gearshift floorplates. Copied from original.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Cowl Vent Gasket
p/n: 40-0210-54
Gasket, cowl vent. Sponge rubber. For cowl vents of thirty-four (34) inch circumference, three fourths (3/4") inch width as shown.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Side Mount Grommet
p/n: 40-0140-37
Grommet, sidemount carrier brace to fender. One and five sixteenths (1-15/16) inch outside diameter by one half (1/2) inch inside diameter.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
2-1/16" Spare Wheel Carrier Grommet
p/n: 32-0253-37
This Spare Wheel Carrier Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for spare wheel carrier mounting bracket.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
9/16" Side Window Upper Weatherstrip
p/n: 40-0280-57
This Side Window Upper Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.