Side Window Weatherstrip Set
p/n: 20-1904-60
This comprehensive, ten (10) piece, Side Window Weatherstrip set is designed from the original part for superior fitment and seal. The anti-rattler set includes front and rear rigid glass run channels, inner and outer window felts and vent window division post seals. Enough parts for both front doors.
Body to Frame Mounting Pad Set
p/n: 20-1871-48
This fifty-eight (58) piece Body to Frame Body Mounting Pad set is designed from the original parts for superior fitment and function. This set includes rubber pads, bolts, and special washers.</p>
Front Door Vent Window Set
p/n: 90-0314-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear Window Gasket
p/n: 20-1776-81
This Rear Window Gasket around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Stabilizer Bar Bushing Set
p/n: 20-1841-33
This twenty-six (26) piece Stabilizer Bar Bushing Set for the front is used to allow the rod to flex and rotate, but stays in place where it is attached to the vehicle frame.
Front Door Vent Window Weatherstrips
p/n: 20-1888-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door Weatherstrips
p/n: 20-1947-72
Door edge weatherstrip. This part is the primary door to body weatherstrip. Top quality rubber with fully molded ends this weatherstrip pair does both front doors.
Windshield Gasket
p/n: 20-1874-50
This Windshield Gasket mounts around the full perimeter of the front glass. The weatherstrip has vulcanized, or bonded, ends which means no cutting or splicing is required. It also has the slot to accommodate the outer edge's decorative molding.
Front Door Inner Dog Leg Weatherstrips
p/n: 20-1767-70
This Front Door Inner Dog Leg Weatherstrip pair is designed from the original part for superior fitment and seal. This rubber weatherstrip installs on inner dog leg of the front door.
Window Felt Beltline Weatherstrip - Left Door
p/n: 20-1903-60
This is a Standard material style left side door window only Window Felt Beltline Weatherstrip pair (also known as beltline weatherstrip). The pair contains one (1) outer piece for door and one (1) inner piece for garnish molding. Includes clips installed and ends bent exactly as original.
Window Felt Beltline Weatherstrip - Right Door
p/n: 20-1902-60
This is a Standard material style right side door window only Window Felt Beltline Weatherstrip pair (also known as beltline weatherstrip). The anti-rattler pair contains one (1) outer piece for door and one (1) inner piece for garnish molding. Includes clips installed and ends bent exactly as original.
Rear Bumper Stone Deflector Seal
p/n: 20-1868-47
This Rear Bumper Stone Deflector Seal install between the body and rear bumper. This seal is an exact reproduction of the original bumper to body seal. The seal comes complete with installation fasteners.
Front Engine Mount
p/n: 20-1786-11
This Front Engine Mount is made of a quality rubber over a metal core to provide maximum life and performance. Two (2) required per car.
Stabilizer Bar Bushing Set
p/n: 20-1717-33
This four (4) piece Stabilizer Bar Bushing set is designed from the original part for superior fitment and function. These are the stabilizer bar to frame mounting bushings.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Side Window Vertical Leading Edge
p/n: 20-1951-80
This side to quarter window Vertical Leading Edge pair attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. This molded rubber weatherstrip pair does not include the chrome piece that attaches directly to the glass.
Quarter Window Pads
p/n: 20-1952-79
This Quarter Window Pad pair is designed from the original part for superior fitment and seal. This is the front lower corner quarter window pad for Hardtops, Convertibles and Retractable models.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Door Glass Run Channel
p/n: 20-1895-58
This Door Glass Run Channel is designed from the original part for superior fitment and function. Part is for the lock side at the rear of the front door. Rigid metal channel with fuzzy flocked lining.
Quarter Window Pads
p/n: 20-3124-79
This Quarter Window Pad pair is designed from the original part for superior fitment and seal. This is the front lower corner quarter window pad for Hardtops, Convertibles and Retractable Hardtop models.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Peel-N-Stick Trunk Weatherstrip
p/n: 20-1389-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Vent division bar weatherstrip
p/n: 20-1893-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Spring Shackle Bushing Set
p/n: 20-1836-32
This Spring Shackle Bushing Set is for the front of the rear leaf spring. One (1) set completes one spring.
Splash Apron
p/n: 20-1867-45
This four (4) piece Splash Apron pair is designed from the original part for superior fitment and seal. Installs on the fender splash apron.
Taillight Mounting Pad
p/n: 20-1793-15
Kit, taillight mounting pad. Fin and Oval type. Six (6) piece set.
Trunk Weatherstrip
p/n: 20-1389-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Transmission Mount
p/n: 20-1269-11
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.
Fender Skirt Edge Weatherstrip
p/n: 20-1862-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. For original skirts only this seal fits between fender skirt and rear fender body.
Spring Shackle Bushing Set
p/n: 20-1834-32
This Spring Shackle Bushing Set is for the rear of the rear leaf spring on car models and the front of the front leaf spring on truck models. Two (2) sets needed per vehicle.
Leaf Spring Clamp Liner Set
p/n: 20-1272-32
A six (6) piece Leaf Spring Clamp Liner Set molded with durable EPDM rubber. These liners are used on Front and / or Rear Leaf Springs on the Driver's or Passenger side.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Fender Anti-Squeak Weatherstrip
p/n: 20-1864-45
This Fender Anti-Squeak Weatherstrip mounts between the front fender splash apron and the front fender. The weatherstrip is an exact reproduction of the original Ford part. Sold as a seventy-two (72") inch strip.
Steering Column Floorplate
p/n: 20-1782-88
Seal, steering column to floor. Installs under floor mat.
Front Suspension Bumper
p/n: 20-0034-32
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1855-42
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood closure and vehicle body cowl.
Window Pinchweld Seal
p/n: 20-1882-52
Seal, garnish molding to dash rubber. Eighty four (84) inches long. Replaces factory #B7A-7003127-E.
Cowl Ventilator Grille Weatherstrips
p/n: 20-1886-54
These Cowl Ventilator Grille Weatherstrips are used to reduce noise from the cowl top ventilator grille. These U-Shaped stripes are designed for a superior fitment and seal.
Door Handle Gasket Set
p/n: 20-1936-69
Pads or gaskets for the outside door handles. Front or rear, this is a four (4) piece set.
Window Sash Channel
p/n: 20-1909-62
This Window Sash Channel is designed from the original part for superior fitment and seal. Thirty-four and three-fourths (34-3/4") inch long EPDM rubber extrusion that goes between glass and metal sash lift channel. One (1) roll required per window.
Window Pinchweld Seal
p/n: 20-1881-52
Seal, garnish molding to dash rubber. Forty six (46) inches long. Models WITH A/C. Replaces factory #B7A-7003127-B.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Axle Rebound Pad
p/n: 20-1287-32
Bumper, rear spring and axle. 1957-59: Full size Fords: Five (5) required per car (1 in center, 2 each side).
Main Wiring Loom Grommet
p/n: 20-1811-20
This Main Wiring Loom Grommet is used to run the main wiring loom to the firewall without being damaged by sheet metal. Designed from original part so it fits correctly.
Ventilator Air Inlet Duct Door Gaskets
p/n: 20-1827-31
This Ventilator Air Inlet Duct Door Gasket pair is designed from the original part for superior fitment and seal. These gaskets seal between the ventilator air inlet duct door to the duct inside.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Rear Spring Pad
p/n: 20-1275-32
This Rear Spring Pad is used as a spring insert silencer. The leaf spring insulator installs between the leaves.
Front Fender Pads
p/n: 20-1866-45
This Front Fender Pad pair is designed from the original part for superior fitment and seal. These weatherstrip pads fit at the top rear of the front fender to cowl panel.
Glovebox or Fuel Tank Filler Door Bumpers
p/n: 20-1220-88
This Glovebox or Fuel Tank Filler Door Bumper pair is a quality reproduction of the original factory part. This push on rubber bumper attaches to support / cushion the glovebox or filler door closure.
Wiring grommet
p/n: 20-1801-17
Grommet, license plate light wire. Installs where wire comes in rear bottom of trunk.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Accelerator Pedal Rod Seal
p/n: 20-1448-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Designed from original part so it fits correctly.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.
Radiator mounting pad
p/n: 20-1873-48
Pads, radiator support to frame. One upper & one lower. Two (2) required per car.
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Front fender center pad
p/n: 20-1865-45
Pads, back center of front fender. Mounts where fender bolts to cowl.
Glovebox Arm Bumper Stop
p/n: 20-1399-88
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Hood bumper
p/n: 20-1309-42
Bumper, hood pull cam. Two (2) required per car.Ford Cars 1957-60 Bumper, hood pull cam. 2 required per car. Ford Cars 1958-59 Bumper, trunk lid.
Spring Shackle or Shock Absorber Link Bushing
p/n: 20-1274-32
This Bushing is manufactured to OEM specifications to install for an authentic fit, finish and function. Used for front or rear leaf spring on Ford models. Used as a rubber, shock absorber link bushing on Chrysler models.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
7/8" Hood Pull Cable / Wiper Motor Firewall Grommet
p/n: 20-2442-20
This Hood Pull Cable / Wiper Motor Firewall Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a hood pull cable and wiper motor firewall grommet.
Body Hole Plug
p/n: 20-1040-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one half (1-1/2") inch in diameter.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
Standard bumper
p/n: 20-1852-41
Bumper, fuel tank filler lid. Gray rubber.Ford Cars 1960-63 Bumper, license plate rubber. Used on rear bumper. 2 required per car.
Brake Adjustment Hole Cover Plug
p/n: 70-1092-24
A quality molded rubber Brake Adjustment Hole Cover Plug that inserts into brake adjustment hole in the backing plate. Most models with drum brakes. Length: 1.25 inches. Height: .875 inches.
License Plate Light or Heater Motor Wire Grommet
p/n: 20-1815-20
This License Plate Light or Heater Motor Wire Grommet is designed from the original part for superior fitment and function. This part functions as a License Plate Light Grommet(s) for Bronco and as a Heater Motor Wire Grommet for 1957-1958 Ford Car models.