Body Weatherstrip Kit
p/n: 90-3120-90
This Body Weatherstrip Kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Front Door Vent Window Set
p/n: 90-0413-90
This Front Door Vent Window Set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0076-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 70-0746-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Rear Window Gasket
p/n: 70-1259-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
Hardtop Roof Rail Weatherstrips
p/n: 50-0331-68
This Hardtop Roof Rail Weatherstrip pair fits on the roof of the vehicle and seals the side window when the window is fully raised.
Front Door Weatherstrips
p/n: 50-0459-72
This Front Door Weatherstrip pair is the primary door to body weatherstrip. A door edge weatherstrip with molded ends. Includes clips and fasteners for easy installation.
Harmonic Balancer - Revulcanization Service Only
p/n: 70-1966-12
This Revulcanization Service Only is designed to restore your Harmonic Balancer to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rear Engine Support Mounts
p/n: 25-0061-11
These Engine Support Mounts pair are fully molded to heavy steel cores as original. The supports are for the rear right and left engine mounts for models with Hydramatic transmission.
Engine Mount Service – Revulcanization Only
p/n: 25-0070-11
This Revulcanization Service Only is designed to restore your Front Lower Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 25-0063-11
This Revulcanization Service Only is designed to restore your Upper Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 25-0073-11
This Revulcanization Service Only is designed to restore your Front Lower Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Prop Shaft Support
p/n: 25-0043-25
Insulator, drive shaft support, center, molded rubber on heavy steel core. Note: Not used on models with Air Ride suspension.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Quarter Window U Jamb Lock Pillar Fillers
p/n: 70-1532-79
This Quarter Window U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This right and left weatherstrip filler mounts at the bottom of the rear side window, lower leading edge to seal the rear quarter window. Also known as a Door U Jamb Seal.
Front Door Auxiliary Weatherstrips
p/n: 70-0551-73
This Front Door Auxiliary Weatherstrip pair fits to the left and right doors at the beltline. Uses snap-in fasteners, four (4) each included.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Vent division bar weatherstrip
p/n: 60-0636-56
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Vent Division Bar Weatherstrip
p/n: 70-0922-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Headlight Ring Gasket Set
p/n: 70-1465-14
This four (4) piece Headlight Ring Gasket Set is designed from the original part for superior fitment and seal. This gasket is for the headlight outer rim to sealed beam headlight retainer ring. Possible fit for models with dual headlights.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Steele exclusive Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. This easy to install weatherstrip mounts around the full perimeter of the trunk directly to the body.
Fender Skirt Edge Weatherstrip
p/n: 60-0201-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrips fits between the removable fender skirt and the rear fender quarter panel.
Front Door Hinge Pillar Weatherstrips
p/n: 70-0552-73
This Front Door Hinge Pillar Weatherstrip pair is designed from the original parts for superior fitment and seal. The pair attaches above the beltline, hinge pillar windshield post. These two (2) strips with pre-installed clips, one for each door, are manufactured for a factory like fit.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Roof Rail Filler
p/n: 70-1763-73
This Roof Rail Filler pair installs on the front corner of the side roof rail, just in front of the flipper seal. Molded as left and right with molded screw holes.
Brake and Clutch Pedal Pads
p/n: 25-0058-22
A pair of brake and clutch pedal pads. Two (2) per car. Length: 4 inches. Width: 2-1/2 inches.
Side Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Splash Apron / A-Arm Dust Shield
p/n: 70-3065-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Door Handle Gasket Set
p/n: 50-0515-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Glovebox Door Link Grommet
p/n: 70-0968-88
This Glovebox Door Link Grommet is designed from the original part for superior fitment and function. Grommet works to cushion the glovebox door closure.
Hood to Fender Bumper
p/n: 25-0091-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Steering Column Gasket - Automatic Transmission
p/n: 70-4467-36
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Body Mount Isolator Pad
p/n: 50-0507-48
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
Body Bolt Cushion
p/n: 60-0189-48
This Body Bolt Cushion is used for each body bolt under frame bracket, to cushion washer and nut. Fully molded from top-quality EPDM rubber with a high level of fit and finish.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Wiper Motor Mounting Gasket
p/n: 70-4466-53
This Wiper Motor Mounting gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality dense rubber to authentic original dimensions. This gasket fits to mount and isolate the wiper motor to the firewall / cowl.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.