Rear Door weatherstrip
p/n: 20-0287-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Front Door Weatherstrips
p/n: 20-0285-72
This Front Door Weatherstrip pair is designed from the original part for superior fitment and seal. These primary door weatherstrips mount (glue-on) directly to the left and right doors sealing the full perimeter of the doors against the vehicle body when the door is closed.
Front Lower Control Arm Bumper
p/n: 20-0202-32
This Front Lower Control Arm Bumper is designed from the original part for superior fitment, finish, and function. This suspension bumper mounts to the front lower control arm to prevent metal to metal contact.
Hood Bumper Set
p/n: 20-0212-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood to Cowl Weatherstrip
p/n: 20-0216-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original Ford part using dense rubber with pre-installed fastener clips.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3690-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Trunk Weatherstrip
p/n: 20-0302-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The decklid weatherstrip mounts around the full perimeter of the trunk directly to the body.
Rear Stone Deflector Rubber Ends
p/n: 20-0237-47
These Rear Stone Deflector Rubber Ends install between the body and rear bumper. The seals are an exact reproduction of the original rear bumper to body seals. One (1) pair needed car.
Radiator Core Support Seal - At Top
p/n: 20-0196-31
This Radiator Core Support Seal is made from quality EPDM rubber to authentic original dimensions. A direct fit piece that mounts on top of radiator core support with the included hardware.
Fuel Tank Filler Pipe Grommet
p/n: 70-5002-39
This Fuel Tank Filler Pipe Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler pipe between the filler neck and vehicle body.
Fuel Tank To Filler Pipe Seal
p/n: 70-5004-41
This Fuel Tank To Filler Pipe Seal is designed from the original part for superior fitment and seal. This part fits around the vehicle fuel filler pipe where the filler pipe enters the fuel tank.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Front Suspension Bumper
p/n: 20-0080-32
Bumper for front suspension upper arm. Measures three eighths (3/8) inch by sixteen (16) by eleven sixteenths with (11/16) inch bolt thread.
Radiator Top Seal
p/n: 20-0200-31
Seal, top of radiator support to radiator seal. Twenty three and thirteen sixteenths (23-13/16) inches long.
Radiator Insulator Pads - Set of 4
p/n: 20-0198-31
This Radiator Insulator Pad set is designed from the original part for superior fitment and function. Molded insulator pads; two (2) long and two (2) short pads for the upper and lower, and for the left and right sides of the radiator. For various applications.
Hood to Fender Bumper Set
p/n: 20-0213-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Bumper
p/n: 20-0211-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Body Hole Plug
p/n: 20-1040-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one half (1-1/2") inch in diameter.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Sun Visor Tips
p/n: 20-2882-88
These Sun Visor Tips are reproductions manufactured to OEM specifications to install for an authentic fit, finish and function. Sold as a pair.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
Rear Side Marker Light Gaskets
p/n: 20-2678-16
This Rear Side Marker Light Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits in the rear between the side marker light and the vehicle body.
5/16" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.