Front or Rear Axle Bumper
p/n: 20-1576-33
This Front or Rear Axle Bumper is designed from the original part for superior fitment, finish and function. An exact reproduction of original. Typically order two per vehicle.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Inner Fender Bumper
p/n: 20-1594-45
This six (6) piece Inner Fender Bumper set is designed from the original part for superior fitment and seal. These rubber bumpers plug into the holes in the inner fender apron to help eliminate squeaks and rattles.
Radiator Grille Pads
p/n: 20-1575-31
This four (4) piece Radiator Grille Pad set is designed from the original part for an authentic fit, finish, and appearance.
Upper Engine Mount
p/n: 20-1538-11
This Front or Rear Upper Engine Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Vent Division Bar Weatherstrips
p/n: 20-0469-56
This Front Vent Division Bar Weatherstrip pair is an extruded rubber strip only that will have to be attached to division post. Sold as a pair for the drivers (LH) and passenger (RH) doors.
Lower Engine Mount
p/n: 20-1539-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Wiper Transmission Gasket
p/n: 20-1609-53
Seal, wiper pivot shaft to roof or cowl. Small type. Replaces factory #11A-17541. Note: this part is used as a wiper pivot shaft to roof in 1937-1939. It is used as a wiper pivot shaft to cowl in 1941-1948.
Wiper Transmission Gasket
p/n: 20-1610-53
Seal, wiper pivot shaft to cowl. Large type. Replaces factory #7C-17541.
Engine Mount Washer
p/n: 20-0442-11
This Front Upper Engine Mount Washer is made of steel. The large upper engine mount insulator sits in this special washer. Fits all Ford 6 cylinder and Flathead V-8 models.
Windshield Wiper Hose Grommet
p/n: 20-1611-20
This Windshield Wiper Hose Grommet is used to run the wiper hose through the firewall. Designed from original part so it fits correctly.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Body Hole Plug
p/n: 20-1040-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one half (1-1/2") inch in diameter.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.
Engine Mount Washer
p/n: 20-0440-11
This Upper Engine Mount Washer is made of steel. Reproduction is designed from the original part to fit correctly.
Glovebox bumper
p/n: 20-2391-88
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Door Check Arm Bumper
p/n: 20-1639-70
This Door Check Arm Bumper is designed from the original part for superior fitment and function. This rubber with arm slot bumper mounts on the door check arm. Works to cushion the door swing.