Hardtop Roof Rail Weatherstrip
p/n: 20-0266-68
This Hardtop Roof Rail Weatherstrip pair is made of high-quality EPDM rubber with molded ends for a factory like fit. These seals fit on the roof of the vehicle and work to seal the side windows when the window is fully raised.
Front Lower Control Arm Bumper
p/n: 20-0202-32
This Front Lower Control Arm Bumper is designed from the original part for superior fitment, finish, and function. This suspension bumper mounts to the front lower control arm to prevent metal to metal contact.
Hood Bumper Set
p/n: 20-0212-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Splash Apron
p/n: 20-0226-44
This Splash Apron pair is designed from the original part for superior fitment and seal. Used to keep road debris from entering the engine compartment.
Hood to Cowl Weatherstrip
p/n: 20-0216-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original Ford part using dense rubber with pre-installed fastener clips.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3690-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Trunk Weatherstrip
p/n: 20-0302-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The decklid weatherstrip mounts around the full perimeter of the trunk directly to the body.
Rear Stone Deflector Rubber Ends
p/n: 20-0237-47
These Rear Stone Deflector Rubber Ends install between the body and rear bumper. The seals are an exact reproduction of the original rear bumper to body seals. One (1) pair needed car.
Radiator Core Support Seal - At Top
p/n: 20-0196-31
This Radiator Core Support Seal is made from quality EPDM rubber to authentic original dimensions. A direct fit piece that mounts on top of radiator core support with the included hardware.
Radiator Side Air Deflector
p/n: 20-0195-31
This three (3) piece Radiator Side Air Deflector set is designed from the original part for superior fitment and function. Left and Right seals are die cut from correct 3/32" masticated rubber to authentic original dimensions. Mounts to core support at side of radiator with included hardware.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Front Suspension Bumper
p/n: 20-0080-32
Bumper for front suspension upper arm. Measures three eighths (3/8) inch by sixteen (16) by eleven sixteenths with (11/16) inch bolt thread.
Radiator Top Seal
p/n: 20-0200-31
Seal, top of radiator support to radiator seal. Twenty three and thirteen sixteenths (23-13/16) inches long.
Hood to Fender Bumper Set
p/n: 20-0213-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood Bumper
p/n: 20-0211-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Quarter Panel Drain Plugs
p/n: 20-2769-45
This Quarter Panel Drain Plug pair is a quality reproduction of the original factory part. These rubber plugs fit inside the quarter panel area to seal-out weather and environmental elements.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Body Hole Plug
p/n: 20-1040-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one half (1-1/2") inch in diameter.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
Sun Visor Tips
p/n: 20-2882-88
These Sun Visor Tips are reproductions manufactured to OEM specifications to install for an authentic fit, finish and function. Sold as a pair.
5/16" Glovebox Door Bumper
p/n: 33-0128-88
This 5/16" Glovebox Door Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a glovebox door bumper on GM models.