Front Door Weatherstrips
p/n: 20-1187-72
This Front Door Weatherstrip pair is the primary door to body weatherstrip. Contains plastic pins that are attached to the door weatherstrips and molded ends with metal cores.
Rear Window Gasket
p/n: 20-1207-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
U Jamb lock pillar filler
p/n: 20-1195-79
Door lock pillar seal. This part seals the bottom of the rear side window, and may also be known as a door jamb seal.
Steering Column At Floor Seal
p/n: 20-1072-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column at the body floor pan.
Spring Shackle and Bushing Set
p/n: 20-2731-32
This Spring Shackle and Bushing Set is for the rear of the rear leaf spring. Designed from original parts for a precise, factory fit. Two (2) sets required per car.
Trunk Weatherstrip
p/n: 20-0302-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The decklid weatherstrip mounts around the full perimeter of the trunk directly to the body.
Accelerator Pedal Pad
p/n: 20-1075-40
This Accelerator Pedal Pad is made of top-quality EPDM rubber with a high level of fit and finish. Designed to be a direct fit reproduction.
Rear Leaf Spring Shackle Assembly
p/n: 20-1066-32
This reproduction Rear Leaf Spring Shackle Assembly is complete with shackle bar plates, rubber bushings and lock nuts. For fitting the suspension leaf spring at its rear spring eye to the vehicle body. Two (2) assemblies required per car.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1088-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This single piece cowl lacing seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl / firewall.
Brake Pedal Pad
p/n: 20-1044-22
Pad, brake pedal. Models with automatic transmission and manual brakes.
Rear Leaf Spring Insulator
p/n: 20-2733-32
This Rear Leaf Spring Insulator is an exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Clutch Lever Dust Boot
p/n: 70-4760-24
This Clutch Lever Dust Boot covers the opening on your engine bellhousing for manual transmission models. A reproduction manufactured to OEM specifications to install for an authentic fit, finish and function.
Clutch Pedal Rod Boot
p/n: 20-1049-23
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Brake Pedal Pad
p/n: 20-1043-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for models with manual transmission and manual drum (not disc) brakes.
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Accelerator Pedal Rod Seal
p/n: 20-2745-41
This Accelerator Pedal Rod Seal is used when running the accelerator rod through the firewall. The seal helps to block out air and wind noise from entering into the cabin.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
Sun Visor Tips
p/n: 20-2882-88
These Sun Visor Tips are reproductions manufactured to OEM specifications to install for an authentic fit, finish and function. Sold as a pair.
Brake Adjustment Hole Cover Plug
p/n: 70-1092-24
A quality molded rubber Brake Adjustment Hole Cover Plug that inserts into brake adjustment hole in the backing plate. Most models with drum brakes. Length: 1.25 inches. Height: .875 inches.