Front Door weatherstrip
p/n: 90-0135-72
Weatherstrip, front door kit. Includes sufficient weatherstrip for door perimeter and hinge pillar. Eight (8) piece kit.
Front Door Vent Window Set
p/n: 90-0328-90
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear door vent weatherstrip
p/n: 30-0118-74
Rear door vent window rubber. Order our #30-0347-74 division post seal separately.
Door Weatherstrip
p/n: 30-0186-73
Weatherstrip, front door to fender (hinge pillar). Soft, solid rubber construction with tabs for all screws, but without metal core.
Windshield Gasket
p/n: 30-0345-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. Fitted gasket provides a formed, seamless seal.
Front Door Vent Window Weatherstrips
p/n: 30-0117-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Rear Window Gasket
p/n: 30-0488-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Vacuum Clutch / Brake Cylinder Diaphragm
p/n: 50-0063-24
This Electromatic Clutch Control or Brake Vacuum Cylinder Diaphragm is designed from the original part for superior fitment and function. Used in different locations dependent upon vehicle make.
Steering Column Grommet
p/n: 70-2523-36
This Steering Column Grommet is designed from the original part for superior fitment and sealing. Fits at the steering column to dash at floorboard. Fully molded with durable black rubber over a metal core.
Axle Rebound Pad
p/n: 30-0125-32
Bumpers, rear axle spring.Length: 5.375 inches. Width: 2.75 inches. Height: 2.1875 inches.
Transmission Mount Service
p/n: 30-0316-24
Insulator assembly, transmission support. Revulcanization service only. Send in your old core for service.
Taillight Mounting Pad
p/n: 30-0266-15
Pads, taillight mounting. For styles without ribbed door lights. Molded left and right.
Front Spring Bumper
p/n: 30-0517-32
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-1690-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The self-adhesive weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Accelerator Pedal Service
p/n: 30-0401-41
Pedal, accelerator. Revulcanization service only. Includes new rod ball socket and pivot. Original pattern tread. Length: 9.625 inches. Width: 1.9375 inches.
Rear Bumper Grommet
p/n: 30-0127-29
Grommets, rear bumper extension bar through rear fender for wrap around bumpers. Fully molded rubber w/ full detail as in original.
Trunk Weatherstrip
p/n: 70-1690-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Division bar grommet
p/n: 70-3135-62
Grommet, rear door vent divider post. Upper and lower, right and left. 4 piece set.
Radiator mounting pad
p/n: 30-0121-31
Grommet, radiator cradle to frame tie rod. 1st type, with locating boss. One four (4) piece set required per car. See also our #30-0309-31.
Engine Mount Pad
p/n: 30-0238-11
This Engine Mount Pad pair is used as a support cushion at the timing gear cover. Correct design and rubber compound. Sold only in pairs. One (1) pair required per car.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Gravel Shield Bumper
p/n: 30-0384-44
Cushion, rear gravel to bumper. Six (6) feet long. One (1) strip required per car.Length: 72.00 inches. Width: .25 inches. Height: .6875 inches.
Front Spring Upper Bumpers
p/n: 30-0516-32
This Front Spring Upper Bumper pair is a quality reproduction of the original factory part. These dense rubber bumpers mount left and right to function as the rebound bumper for the front springs.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Rigid Run Channels
p/n: 30-0023-57
This Rigid Run Channel pair for the division bar is un-beaded, steel core, plush lined, and cloth covered. Available as 28" pair.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
3" Firewall Grommet
p/n: 30-0110-42
This Firewall Grommet pair is used for the hood lock link through the firewall. Designed from the original part for superior fit and seal.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Ignition Cable Grommet
p/n: 70-1598-21
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Flexible Run Channel - 6 Ft.
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Engine Snubber Pad Set
p/n: 30-0311-11
This four (4) piece Engine Snubber Pad Set is designed from original for correct fit and function. Sold only in complete sets. One four (4) piece set required per car.
Vent division bar weatherstrip
p/n: 30-0346-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 30-0347-74
Weatherstrip, rear vent window, front edge (on division post) right and left.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Gearshift Boot
p/n: 30-0412-24
Grommet, shifter shaft to shroud. One (1) per car.Length: 4.125 inches. Width: 2.3125 inches.
License Light Mounting Pad
p/n: 30-0122-17
Pad, rear license light mounting, with correct dimensions and beading.Length: 8.125 inches.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Decklid Lock / Handle Mount Gasket
p/n: 30-0126-87
This Decklid Lock / Handle Mount Gasket is designed from the original part for superior fitment, finish and function. Length: 4 inches.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Flexible Run Channel - 5ft.
p/n: 70-1107-57
A cloth covered and mohair-lined type Flexible Run Channel. For sides and top of side windows. Available in 5- foot lengths.
Antenna Mount Pad
p/n: 70-2621-21
Pad, roof mounted antenna gasket. Models with antenna mounted above center of windshield.
Brown Gearshift Boot - Steering Column
p/n: 30-0069-89
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Brown rubber. Two and one quarter (2-1/4) inches long.
Hood Rest Pad
p/n: 30-0092-42
Hood Rest Pad. Molded rubber with a steel core. Six (6) required per car. Length: 1.75 inches Width: 1.625 inches.
2-1/2" Firewall Grommet
p/n: 30-0111-21
This Firewall Grommet is used to run the speedometer cable through the firewall. The grommet is retained by a steel collar, not included.
1-9/16" Firewall Grommet
p/n: 30-0383-21
This Firewall Grommet is used to run the vacuum antenna line through the firewall. The grommet is molded with four (4) holes but three (3) are left masked for use if needed.
Black Gearshift Boot - Steering Column
p/n: 30-0069-36
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Black rubber. Two and one quarter (2-1/4) inches long.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Stabilizer Grommet
p/n: 70-0221-33
Grommet, rear stabilizer bar (angular sway bar). Four (4) required per car. Fully molded rubber.
Antenna Mount Pad
p/n: 30-0502-21
Pad, antenna mounting on fender. For fender mounted antennas only.
Rear Spring Pad
p/n: 30-0452-32
Insulator, rear spring leaf clip. Seven and one half (7-1/2) inch long, customer may trim for shorter lengths. May use up to eight (8) per car.
Stabilizer Grommet
p/n: 30-0310-33
Grommet, front or rear stabilizer links, lower. Fully molded rubber.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Black Door Lock Knob
p/n: 30-0251-71
Knob, inside door lock control, flexible rubber, black only.Height: 1.125 inches.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Overdrive Linkage Grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
11/16" Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
3/4" Trunk Weatherstrip
p/n: 30-0356-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.