Body Weatherstrip Kit
p/n: 90-3139-90
This Body Weatherstrip Kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Front Door Vent Window Set
p/n: 90-0410-90
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Rear Window Gasket
p/n: 60-0498-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. This is for vehicles with the upper inside garnish molding.
Hardtop Roof Rail Weatherstrips
p/n: 70-0611-68
These Hardtop Roof Rail Weatherstrips fit on the roof of the vehicle and seal the side windows when the window is fully raised.
Windshield Gasket
p/n: 70-0671-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0071-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door Weatherstrips
p/n: 70-0745-72
This Front Door Weatherstrip pair is the primary door to body weatherstrips. It has molded ends and includes 6 pins and 24 sockets for easy installation. Made of top-quality rubber.
Transmission Mount Service
p/n: 50-0429-25
Transmission mount. Revulcanization service only.Length: 8.0 inches. Width: 3.0625 inches.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-3061-45
This comprehensive ten (10) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right made pieces fit over suspension a-arms and inside front inner fenders.
Support Arm Bumper
p/n: 50-0526-32
Bumper, lower support arm. With metal core and attaching bolt. One (1) pair per car.Width: 2.4375 inches. Height: 4.0 inches.
Track Bar Bushing
p/n: 50-0527-34
Bushing, track bar. Molded out of BUNA rubber with correct metal sleeve like original.Height: 1.875 inches.
Front Door Hinge Pillar Weatherstrips
p/n: 60-0326-73
This Front Door Hinge Pillar Weatherstrip set fits at the front door opening. Auxiliary on door hinge pillar at beltline, right and left. Sometimes called "L" or "J" strips. Fully molded with authentic configuration to help guide water to the outside of vehicle.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Upper Lock Pillar Filler
p/n: 70-0782-79
A fully molded Upper Lock Pillar Filler pair. One and five eighths inch (1-5/8") wide and two- and three-quarter inches (2-3/4") high. This part seals the bottom of the rear side window and may also be known as a door jamb seal.
Vent division bar weatherstrip
p/n: 60-0636-56
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Taillight Lens Gasket
p/n: 70-1793-15
Gasket, taillight lens. Made of die cut sponge rubber to original configuration.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Steele exclusive Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. This easy to install weatherstrip mounts around the full perimeter of the trunk directly to the body.
Rear Bumper Gravel and Splash Guard Shields
p/n: 70-1279-30
This two (2) piece Rear Bumper Gravel and Splash Guard Shield pair is designed from the original part for superior fitment and seal. Twenty-two (22) inches long per side.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Hood To Cowl Weatherstrip
p/n: 50-0495-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This 48” long x 1-1/8” wide weatherstrip provides complete coverage.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Firewall Grommet
p/n: 70-1914-20
This Firewall Grommet is used for running the heater control cabled wiring harness through the firewall. Designed from the original part for superior fit and seal.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 50-0506-48
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable.
Side Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Folding Seat Back Frame Bumper
p/n: 70-2579-88
A Folding Front Seat Frame Rest Cushion Bumper manufactured from dense rubber with a molded in metal retaining washer. Two (2) used per vehicle.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Body Mount Isolator Pad
p/n: 50-0507-48
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Strut Rod Bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Hood Bumper
p/n: 50-0489-42
Bumper, hood to fender ledge. Number required varies. Molded rubber type.Width: 1.5 inches. Height: 1.0 inches.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Hood To Fender Bumper
p/n: 50-0473-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure.