Body Mount Pad Fittings
Mount, rear cab to frame. Revulcanization service only.
Kit, cab to frame pad and bolt. For 2 W/D (wheel drive) only. Thirty-two (32) piece set.
Pad kit, radiator support to frame. Fits 1973-76 F100 2-wheel drive, but will work for F250 through F350 but must add extra metal washers.
Kit, cab to frame pad and bolt.
Pads, body mounting for front bracket, right and left. Three eighths (3/8) inch by two and three fourths (2-3/4) inch by four (4) inches with two (2) collars and retaining rings. Two (2) required per car.
Grommet, radiator cradle to frame tie rod. 1st type, with locating boss. One four (4) piece set required per car. See also our #30-0309-31.
Webbing, body to frame. Two (2) inch wide, twenty five (25) foot long roll.
Grommet, several useages. Radiator core cradle tie rod to frame or rear stablizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set. One and three eighths inch (1 3/8") outside di
Shim, radiator core mounting stud spacer. Fully molded rubber. Use as required. Comes as a pair of two (2). Two and seven eighths inch (2 7/8") square by five eighths inch (5/8") inside hole diameter by three eighths inch (3/8") height.
Pads, insulator body mount. Three piece set includes a replacement for an upper, a middle insulator, and for a bottom cone shaped insulator.
Bumper, cab hold down bolts. Comes as a pair of two (2). Fully molded rubber. One and five eighths inch (1 5/8") outside diameter by three eighths inch (3/8") inside hole diameter by one and one thirty-two seconds inch (1 1/32") height. Chevrolet/GMC Tru
Pad, body mounting, for body bracket. Two (2) collars and retaining rings. Four (4) per car.
Body bumpers, rear, at body hold-down bolt. Fully molded rubber. Comes as a pair of two (2). One and three fourths inch (1 3/4") outside length by one and one fourth inch (1 1/4") diameter by three eighths inch (3/8") inside hole diameter.
Pads, insulator rear body mounts. Comes as a two (2) piece set. Two (2) sets required per car. Both pieces are made of fully molded rubber. Circular mount measures: two and one half inch (2 1/2") outside diameter by one inch (1") inside hole diameter by f
Cushion assembly body mounting pad. Fully molded rubber with metal core, locating collar and metal bolt sleeve. Rectangular. Three inches (3") length by two inches (2") width. Seven sixteenths inch (7/16") inside hole diameter by five eighths inch (5/8")
Seal pad, rubber tape. Fifteen (15) foot roll.
Pad, body mounting. Three eighths (3/8) inch by two (2) inch by three (3) inch with collar and retainer ring.
Pad, body mounting. Fully molded rubber with metal core. Number used varied according to body type. Two inch (2") outside diameter by three fourths inch (3/4") inside top hole diameter by one half inch (1/2") bottom hole diameter by three fourths inch (3/
Pad and steel bushing assembly. Two (2) required per vehicle Rectangular rubber with metal core, locating collar and metal bolt. Two and seven sixteenths inch (2 7/16") length by one and three fourths inch (1 3/4") width by three fourths inch (3/4") ins
Pad, body bolt insulator. Metal core & locating collar covered with rubber. Number used varies per car. Two inch (2") square by seven eights inch (7/8") locating collar outside diameter by five eighths (5/8") locating collar inside hole diameter. Five eig