Hardtop Roof Rail Weatherstrip
p/n: 70-1676-68
Hardtop roof rail weatherstrip. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Hardtop Roof Rail Weatherstrips
p/n: 82-0209-68
This Hardtop Roof Rail Weatherstrip pair is made of high-quality EPDM rubber with molded ends for a factory like fit. This part fits on the roof of the vehicle and seals the side window when the window is fully raised. For models with stationary (fixed) rear quarter windows.
Harmonic balancer service
p/n: 40-0372-12
Vibration Damper (crankshaft impulse neutralizer assembly). Revulcanization service only.
Headlight Bracket Pad
p/n: 40-0236-14
Pad, headlight bracket seal. Without metal core. One (1) pair per car.Length: 5.75 inches.
Headlight Grommet
p/n: 40-0009-14
Grommet, headlight bar to shell. One and one fourth (1-1/4) inch round hole.
Headlight Grommet
p/n: 40-0008-14
Grommets, headlight bar to shell. Slightly oval. One and one fourth (1-1/4) inch diameter hole.
Headlight Mounting Pad
p/n: 40-0219-14
Mounting pad, headlight body to bracket. Without steel core.Length: 5.625 inches.
Headlight Mounting Pad
p/n: 40-0059-14
Pad, headlight bar to fender mounting. Four and three fourths (4-3/4) inch by one and one fourth (1-1/4) inch.Length: 4.75 inches. Width: 1.25 inches.
Headlight Mounting Pad Service
p/n: 40-0312-14
Anchor pad, head light crossbar to radiator shell. Right and left. Revulcanization service only.
Hinge Pillar Weatherstrip
p/n: 70-1811-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hinge Post Weatherstrip
p/n: 70-1769-73
Weatherstrip, body hinge pillar, lower (front door).Length: 10.125 inches.
Hood Bumper
p/n: 40-0503-42
Bumper, hood to fender ledge. Correct original cross-section. Up to ten (10) required per car.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Hood Bumper
p/n: 40-0164-42
Pad, hood panel center bracket. Hollow, to fit over original steel bracket.Length: 1.375 inches. Width: 1.375 inches.
Hood Bumper
p/n: 40-0354-42
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Hood Bumper
p/n: 70-1607-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to support / cushion the hood closure.
Hood Bumper
p/n: 40-0118-42
Bumpers, hood top panel to side panels. Four (4) piece set with brass core as original. Four (4) per vehicle.
Hood Bumper
p/n: 40-0313-42
Bumper, hood panel assembly. Same as our #40-0164-42. (except vulcanized to brass cores). Length: 1.375 inches. Width: 1.3375 inches.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Hood Corner Pad
p/n: 40-0090-42
Pads, hood rear corners. Open angle for long hood. Metal core as original.Length: 1.50 inches.
Hood Corner Pad
p/n: 40-0089-42
Pads, hood front corners. Rubber with metal core as original.Length: 1.4375 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood Corner Pads
p/n: 40-0187-42
This Hood Corner Pad pair is an exact copy of the original. This pad fits between the engine hood and the body to isolate noise and vibration.
Hood latch swivel
p/n: 70-0061-42
Swivel, hood latch. Exact copy from .075 steel, pierced for rivets, not plated.
Hood Support Rod Top Cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Hood to Cowl Weatherstrip
p/n: 70-2236-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 70-2341-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. A proper extrusion approximately sixty-two (62) inches long with pre-installed fastener clips.
Hood to Cowl Weatherstrip
p/n: 70-2219-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This six (6) long original profile extrusion provides complete coverage.
Hood to Cowl Weatherstrip
p/n: 40-0470-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This six (6) foot long x 13/16” wide weatherstrip provides complete coverage.
Hood to Cowl Weatherstrip
p/n: 40-0475-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip can also be used as a radiator seal. Available by the foot.
Hood to Fender Bumper
p/n: 60-0542-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 70-2043-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper Set
p/n: 70-2315-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Fender Bumper Set
p/n: 70-2672-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Hood to Radiator Weatherstrip
p/n: 70-1580-42
Weatherstrip, hood to radiator shroud.Width: 1.3125 inches.
Hood to Radiator Weatherstrip
p/n: 40-0512-42
Weatherstrip, hood to grill or radiator shroud. Two (2) pieces, each sixteen (16) inches.Width: 1.3125 inches.
Hood to Radiator Weatherstrip
p/n: 70-2073-42
This Hood to Radiator weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the front of the engine bay directly to the radiator support.
Hood to Radiator Weatherstrip
p/n: 70-2385-43
Weatherstrip, hood to radiator. Proper rubber cross section with pre-drilled holes, cut outs and included attaching clips.Length: 61.25 inches.
Hood to Radiator Weatherstrip
p/n: 70-2386-43
Weatherstrip, hood to radiator. Proper rubber cross section with pre-drilled holes, cut outs and included attaching clips.Length: 62.875 inches.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Inner Side Window Bumper
p/n: 70-0775-62
Bumper, inner side window garnish molding. One (1) per door.Length: 1.0 inches. Width: .3125 inches. Height: .25 inches.