Search Results
Please click on the part name in red in order to get a complete description.
Trunk or hood bumper
p/n: 34-0203-42
Bumper, trunk or hood. Molded with clearance for screw. Used for: Buick 1942-50 Bumper for trunk. Chevrolet 1949-55 Bumper for rear hood corners on cowl. Chevrolet 1949-50 Bumper for trunk. Oldsmobile 1938 Bumper under hood corner on radi
Inner side window bumper
p/n: 70-0775-62
Bumper, inner side window garnish molding. One (1) per door.Length: 1.0 inches. Width: .3125 inches. Height: .25 inches.
Convertible rail grommet
p/n: 32-0132-67
Grommet, upper side rail, for styles with removable rails. Sheet Metal Hole: 1/2" Center Hole: 3/8" Outside Diameter: 13/16" Slot Width: 3/32"
Side window weatherstrip
p/n: 70-0064-57
Seal, lower side window. Fastens to inner face of door to seal against outer side of glass. Also used as weatherstrip on crank-up windshield tops.
Side window weatherstrip
p/n: 70-0079-58
Weatherstrip, side window lower edge, retained in metal flap on side of carrier channel, seals out water when window is cranked up.Width: .375 inches.
Wiring grommet
p/n: 32-0047-14
Grommet, electric wire through body for head and taillights. Sheet Metal Hole: 11/16" Center Hole: 3/8" Outside Diameter: 1" Slot Width: 1/16"
Windshield weatherstrip
p/n: 19-0023-73
Weatherstrip, windshield, T-rubber, short style. Seven sixteenths (7/16) inch high.Height: .4375 inches.
Windshield weatherstrip
p/n: 19-0024-52
Weatherstrip, windshield, largest type of T-rubber, one and one half (1-1/2) inch high.
Windshield weatherstrip
p/n: 70-1163-52
Weatherstrip, T-rubber, one (1) inch long with one quarter (1/4) inch top. Numerous applications for windshields.Width: 1.0 inches.
Windshield weatherstrip
p/n: 70-0142-52
Weatherstrip, T-rubber, windshield. Three fourth (3/4) inch size, top width is approximately one fourth (1/4) inch.Width: .75 inches.
Firewall grommet
p/n: 32-0133-21
Special grommet with wide spacing for frame metal, to pass electrical wiring and cables through frame. Sheet Metal Hole: 31/32" Center Hole: 3/4" Outside Diameter: 1-3/16" Slot Width: 3/16"
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Filler and cushion strip
p/n: 70-1236-48
Filler and cushion strip, many applications. One sixteenth (1/16) inch by one and three eighths (1-3/8) inch.
Filler and cushion strip
p/n: 70-1237-48
Filler and cushion strip, many applications. Five thirty seconds (5/32) inch by one and five eighths (1-5/8) inch.
Clutch release bearing grommet
p/n: 32-0342-24
Grommet, clutch release bearing grease tube through side of bell housing. Sheet Metal Hole: 3/4" Center Hole: 3/8" Outside Diameter: 1" Slot Width: 3/16"
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Firewall grommet
p/n: 32-0134-20
Special grommet with wide spacing for frame metal to pass electrical wiring and cables through frame. Sheet Metal Hole: 1-1/16" Center Hole: 13/16" Outside Diameter: 1-5/16" Slot Width: 5/32"
Fuel line grommet
p/n: 32-0714-41
Grommet, fuel line and other uses through firewall. Sheet Metal Hole: 1" Center Hole: 3/8" Outside Diameter: 1-5/16" Slot Width: 1/16"
Headlight grommet
p/n: 32-0039-14
Grommet, headlight and horn conduit through fender, made to clear nut on end of conduit. Three (3) per car. Sheet Metal Hole: 15/16" Center Hole: 1/4" Outside Diameter: 1-1/4" Slot Width: 1/16"
Hood latch swivel pad
p/n: 34-0408-42
Pad, hood latch swivel for hood latch pressure against hood corners. For screw or rivet.
Firewall grommet
p/n: 32-0001-37
Grommet, firewall and spare wheel sidemount. Sheet Metal Hole: 1-1/8" Center Hole: 3/4" Outside Diameter: 1-9/16" Slot Width: 1/16"
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Firewall grommet
p/n: 32-0422-20
Grommet, firewall, speedometer cable through firewall. Two (2) used per car. Sheet Metal Hole: 1-3/16" Center Hole: 1/2" Outside Diameter: 1-7/16" Slot Width: 1/4"
Side Window Upper Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 40-0280-57
Side window weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Side roof rail weatherstrip
p/n: 11-0010-57
Weatherstrip, side window, (possibly used on other coachwork). Exact copy of original, top quality, fine detail. Murphy-bodied Duesenberg Convertibles.
Channel filler weatherstrip
p/n: 30-0154-57
Filler, for glass channel for convertible type windows with metal frame around one fourth (1/4) inch glass.Width: .4375 inches. Height: .50 inches.
Channel filler weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel.Width: .375 inches. Height: .
Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel.Width: .375 inches. Height: .6875 inches.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Pressure ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Door check link rod end stop
p/n: 70-0325-70
Pad, door check link. For rod type door check. One (1) inch diameter by three eighths (3/8) inch thick with five sixteenths (5/16) inch hole.
Side roof rail weatherstrip
p/n: 70-0081-67
Weatherstrip, side window.Length: 1.4375 inches. Width: .625 inches.
Universal Mounting Pad
p/n: 70-0019-52
Pad, universal mounting, two and one eighths (2-1/8) inches wide. Heavy rubbery pad with half round (3/16) inch bead for windshield frame mounting to cowl on open cars. Black rubber.
Rear spring thrust washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Rear spring thrust washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Hood bumper
p/n: 60-0034-42
Bumper stop, hood, lower center. Two (2) required per vehicle.Length: 1.0 inches. Width: .75 inches. Height: .4375 inches.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Door bumper
p/n: 30-0312-71
Pad, door jamb. Usually requires two (2) per door.Length: 1.0 inches. Width: 1.0 inches. Height: .50 inches.
Spare wheel carrier grommet
p/n: 32-0040-37
Grommet, spare wheel brace for sidemount wheels, at runningboard apron, four (4) per car. Sheet Metal Hole: 1-1/2" Center Hole: 1/2" Outside Diameter: 1-13/16" Slot Width: 1/16"
Door handle grommet
p/n: 70-0009-69
Grommet, for outside door handle ferrule (our #70-0111-69, ordered separately). Molded rubber with cloth covering per original.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Side roof rail weatherstrip
p/n: 70-0060-65
Weatherstrip, side roof rail. Made from dense rubber extrusion.Width: 1.0 inches. Height: .6875 inches.
Side window roller
p/n: 70-0117-62
Anti-rattle roller, side windows. Rubber only, replaces original perfectly and easily. Fits both styles of brackets.
Door bumper
p/n: 60-0032-71
Pad, door jamb. One (1) per door.Length: 1.25 inches. Width: .75 inches. Height: .875 inches.
Door alignment pad
p/n: 60-0060-71
Wedge pad, door aligning dovetail. Goes under bumper retainer.Length: .9375 inches. Width: .9375 inches. Height: .4375 inches.
Door bumper
p/n: 34-0025-42
Bumper, front and rear body hinge pillar, one (1) inch diameter by one fourth (1/4) inch thick, held by screw, steel core. Auxiliary, used only where needed to prevent door rattle.Note: also used on 1942-50 Packards with Clipper styling near t
Fabric hood lacing
p/n: 70-2221-42
Lacing, hood, fabric, webbing anti-squeak. DOES NOT have hollow center. Fasten with rivets if so found originally. Excellent quality.
Fabric hood lacing
p/n: 60-0578-42
Lacing, hood, fabric, webbing anti-squeak. With hollow center to receive wire if needed, or fasten with rivets if so found originally. Excellent quality. Seven eighths (7/8) inch by one eighths (1/8) inch thick.
Door bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Door Bumper
p/n: 70-1156-71
Pad, door side bumper. Clip retained. Appears identical to Atwood #107, #208.Width: 1.5 inches. Height: 1.3125 inches.
Side window run channel
p/n: 70-1169-58
Channel, side window, pre-flocked, nine sixteenths (9/16) inch wide to accommodate metal frame side window.
Side window header channel
p/n: 70-0306-58
Header channel, side window, superior quality plush lined rubber channel for across top of doors above side windows on closed bodies.
Side window run channel
p/n: 70-1168-58
Channel, side window, pre-flocked, five sixteenths (5/16) inch wide base for one fourth (1/4) inch glass. Most Fisher closed bodies except those using stainless beaded channel. For nine sixteenths (9/16) inch wide channel, see our #70-1169-58.
Door and trunk handle gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Door bumper
p/n: 30-0350-71
Bumper, door dovetail. Goes in door opening, two (2) door, under steel cap in dovetail receiver.Width: 1.125 inches. Height: .9375 inches.
Motor mount pad
p/n: 11-0027-11
Mounting pad, engine. Three eighths (3/8) inch hole, one and five eighths (1-5/8) inch outside diameter.
Door bumper
p/n: 70-1157-71
Pad, door jamb (door side bumper).Some bodies using escutcheons around pads.Length: 1.5625 inches. Width: 1.1875 inches.
Shock and stabilizer bushing
p/n: 50-0220-32
Bushing, for shock absorber link cross pin or stabilizer link cross pin.1931-36 Bushing, rubber, for shock absorber link cross pin, #41151.
Door check link rod end stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Motor mount pad
p/n: 11-0029-11
Mounting pad, engine. One half (1/2) inch hole, one and five sixteenths (1-5/16) inch outside diameter. Original pattern, superior workmanship.
Tan bowdrill cloth tape
p/n: 70-1173-65
Tape, brown (tan) bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such
Door bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Door bumper
p/n: 40-0042-70
Pad, door jamb. Earlier type, screw retained, perfect copy.Length: 1.50 inches. Width: 1.25 inches.
Door handle ferrule
p/n: 70-0111-69
Ferrule, for three fourths (3/4) inch outside door handle. Chrome plated brass. (See #70-0009-69 for grommet). Used for outside door handle or outside trunk handle.
Shock absorber bushing
p/n: 40-0273-32
Bushing. shock absorber link, smaller type. Eight (8) required per car. Compare with our #40-0069-32 (larger type).Length: .9375 inches. Width: .
Starter button cover
p/n: 60-0358-21
Cover, starter rod button, round slip over type. One and seven sixteenths (1-7/16) inch outside diameter. Good copy with bow tie center.Height: .
Bowdrill cloth tape
p/n: 70-1172-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Motor mount pad
p/n: 11-0028-11
Mounting pad, engine. One half (1/2) inch hole, one and five eighths (1-5/8) inch outside diameter. Original pattern, superior workmanship.
Door bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Brake shaft stop bumper
p/n: 70-0271-24
Bumper, brake rocker shaft lever stop. Two (2) used per car. Also used as door side bumper for some 1927-31 Cadillacs.
Channel filler weatherstrip
p/n: 20-2091-62
Seal, door glass to body. Fits in metal channel that holds glass. Also functions as the door to window seal when window is rolled up. Sold in a 36 inch strip.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Shock absorber bushing
p/n: 40-0069-32
Bushing, shock absorber link, flanged at both ends. Seven eighths (7/8) inch long between flanges, one (1) inch diameter barrel.
Firewall grommet
p/n: 30-0093-21
Grommet, firewall. For various rods and tubing including ignition advance.Length: 1.125 inches.
Starter button cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Door alignment pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Shock absorber arm bushing
p/n: 15-0005-33
Bushing, shock absorber arm ball joint.Height: .875 inches.