Please click on the part name in red in order to get a complete description.
Grommet, firewall. For various rods and tubing including ignition advance.Length: 1.125 inches.
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Bumper, hood side panel. Metal core as original, six (6) per car.
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Bumper, rumbleseat lid. Sometimes used on trunk. One half (1/2) inch by one (1) inch by one (1) inch. Two (2) per car.Length: 1.0 inches. Width: 1.0 inches.
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Pad, door jamb, large size, retained by both dovetail retainer from back, and screw through center. Usually 2 per door.Length: 2.125 inches. Width: 1.
Spacer, steering column to dash at U-clamp.Length: 2.50 inches.
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Cover, accelerator rod button. Round slip-over type. Good copy with bow tie center.Height: .4375 inches.
Swivel, hood latch. Exact copy from .075 steel, pierced for rivets, not plated.
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Grommet, water temperature indicator pipe through dash.
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Bushing, brake cross shaft bracket.
Grommet, firewall pass through, rectangular. Also see our #40-0522-21 for larger type if needed.
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Five (5) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our #70-1170-99 or
Pad, rumbleseat lid corner, Compare with our #60-0191-87.Length: .75 inches.
Pad, body mounting. Three eighths (3/8) inch by two (2) inch by three (3) inch with collar and retainer ring.
Cushion, horn blowing button.Height: 1.0 inches.
Channel, side window glass, vertical run. (Use our #40-0280-57 across top).
Pad, luggage rack to rear apron.
Headlight bracket-to-fender pad. POA #1245890-1, right and left.
Bushing, headlight to badge bar.
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.
Pad, fender well for sidemounted spares. One (1) pair per fender.Length: 2.875 inches. Width: 2.875 inches. Height: .4375 inches.
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Grommet, firewall. For coil wire and temperature gauge line. Excellent workmanship and correct design.Height: 1.0 inches.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Bumper, inclined toe board pedal hole, carried on toe board to meet our #30-0055-24 pedal. dust cover.
Grommets, horn wire exit from horn motor cover.
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Bumper pad, rumbleseat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Cover, starter cable terminal post inside to frame. Full detail and molded as original part.
Gasket, cowl vent. Sponge rubber, good copy of original. Thirty seven and one half (37-1/2) inch developed length.Length: 37.50 inches.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Pads, brake and clutch pedals. One and seven eighths (1-7/8) inch by four (4) inch overall. Excellent detail with bowtie emblem like original.
Body bumpers, rear, at body hold-down bolt. Fully molded rubber. Comes as a pair of two (2). One and three fourths inch (1 3/4") outside length by one and one fourth inch (1 1/4") diameter by three eighths inch (3/8") inside hole diameter.
Pad, starter pedal. Original pattern. Round style.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Pad, body mounting, for body bracket. Two (2) collars and retaining rings. Four (4) per car.
Grommet, steering column at floor.Length: 3.375 inches.
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Bushing, rear spring front eye, inlox cartridge type as original.
Grommet, firewall, 6-hole type.Length: 5.0 inches.
This golf bag door weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.
Headlight tube flange gasket. Two (2) per car. Replaces #1234556.
Inner Fender Seal for anti-rattle, runningboard apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Dust cover, gearshift lever.
Bumper, trunk lid, rubber. Retained by two (2) screws (not included).Width: 2.50 inches. Height: 1.625 inches.
Pad, starter pedal, snap over cover with tread pattern matching other pedals.Length: 2.25 inches.
Mounting pad, engine. Original pattern, superior workmanship.Qty Required:2 Height: 1.875 inches.
Dust cover, gearshift lever. Elbow type.
Cushion, sidemount clamp. Two and one eighth (2-1/8) inch by four and five eighths (4-5/8) inch.Length: 4.625 inches. Width: 2.125 inches.
Pad, rumbleseat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Gaskets, taillight mounting under fender wire conduit base.Width: 3.25 inches.
Pad, rumbleseat step plate mounting, rectangle type for top of fender.Length: 4.875 inches. Width: 4.25 inches.
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Grommet, fuel filler neck. Oblong, fully molded rubber. Four and one eighth inch (4-1/8") outside length by two and one fourth inch (2-1/4") inside diameter.
Bumper, front spring to frame. Two (2) required per vehicle.
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Grommet, firewall pass through, rectangular. Large type. Also see our #40-0523-21 for smaller type if needed.
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Grommet, steering column at floor. One and one half (1-1/2) inch tube.
Anti-rattle, spare wheel cover in fenderwell.Width: .25 inches.
Mount, transmission. Original pattern, superior workmanship.
Pad, accelerator pedal. Cements and fastens with screws to original metal pedal.Length: 6.50 inches.
Weatherstrip, cowl vent. Top quality sponge rubber.
Cover, brake master cylinder filler and inspection hole. Metal core as original.
Pad, rumbleseat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Grommet, side carrier brace rod.
Bumper, front spring. Fits onto original bracket.Length: 2..125 inches. Width: 2.0 inches. Height: 1.875 inches.
Weatherstrip, fixed back and quarter windows, plain type. Seven and one half (7-1/2) foot strip.Length: 90.0 inches. Width: .5625 inches. Height: .
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Grommet, fuel filler neck. 2-5/8" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Weatherstrip, stationary quarter windows. Eight (8) foot strip for two (2) quarter windows. Most models with stationary windows.Length: 96.0 inches.
Accelerator pedal pad manufactured in Black rubber. Full slip-over type and a perfect copy. For Brown see our #50-0080-89.
Seal or Cushion, gearshift to floorboard.Length: 12.75 inches.
Pad, spare wheel standoff post at cowl.
This rear window gasket weatherstrip comes in a seven foot, three inch (7' 3") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Grommet, steering column at floor.
Cover, rear apron over fuel tank. 3-1/2 inch diameter hollow cup to cover hole above fuel gauge sending unit.
Cover seal, vacuum brake valve operating rod.
Weatherstrip or rubber buffer, rumbleseat opening notch-out on perimeter of opening near water catch rail. Two (2) used per car.
Pad, brake and clutch pedals. Horizontal oval style, slip over type.Length: 3.8125 inches. Width: 2.375 inches.
Grommet, steering column floor, black rubber only, excellent copy of original.Length: 5.0 inches.
Grommet, headlight bar to shell. One and one fourth (1-1/4) inch round hole.
Weatherstrip, lower windshield. Four (4) foot strip.
Accelerator pedal pad manufactured in Brown rubber. Full slip-over type and a perfect copy.
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Gasket, cowl side ventilator. One eighth (1/8) inch sponge rubber.Length: 11.375 inches. Width: 4.625 inches.
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Grommet, steering column clamp at dash, one and three fourths (1-3/4)inch wide for one and three fourths (1-3/4)inch column.Length: 6.125 inches.
Pad, rumbleseat step slip over style for original core, "DB" logo.
Pad, brake and clutch pedal. See also our #40-0072-22.Length: 3.8125 inches. Width: 2.3125 inches.