Search Results
Side mount spare wheel grommet
p/n: 70-0341-37
Grommets, sidemount. These are the very large type, right and left. Used simultaneously with our #70-0388-37. Compare with your original. (See also our #70-0388-37).
Side Mount Spare Wheel Grommet
p/n: 70-0388-37
Grommets/seals, for sidemounted spares, cover hole in fender. Large, fully flanged for fender metal, compare to our #70-0341-37 and your original. Symmetrical, right and left. Approximately five and three fourths (5-3/4) inches by eight (8) inches outside
Headlight mounting pad set
p/n: 70-0101-14
Mounting pad set, headlight and headlight bracket. Light pad has metal core and high collar as original to accommodate headlight adjustment.
Side window run channel kit
p/n: 90-0140-58
This eight (8) piece kit includes the inner and outer windowfelts, upper rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door. Models with wood in the doors use our #70-1168-58 as lower rigid run channel.
Front spring bumper
p/n: 70-0339-32
Bumper, front spring, upper arm on frame. Rubber with heavy steel core, including five sixteenths (5/16) inch stud.
Front Door Vent Window Kit
p/n: 90-0377-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0032-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Ferrule installing tool
p/n: 70-0662-69
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Motor mount service
p/n: 70-0724-11
Pad, motor support, rear. Revulcanization service only. Send in your old plates with studs intact. Rebound cushion, furnished with mount.
Rear Window Gasket
p/n: 70-0673-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Side mount spare grommet kit
p/n: 70-0180-37
Grommet kit, rear spare wheel mount for cars without luggage rack. Three (3) piece set consisting of two (2) large grommets, one (1) small grommet.
Hood center protector
p/n: 70-0342-42
Protector, hood center. Brass core as original threaded to fit original screws.
Shock and stabilizer seal
p/n: 70-1185-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.
Air inlet hose
p/n: 70-0405-41
Hose, air inlet, radiator shroud to air silencer. Two and one eighths (2-1/8) inch outside diameter by nine and three eighths (9-3/8) inch long. Beautiful copy of rare original part.
Luggage rack grommet
p/n: 70-0287-46
Grommets, luggage rack brace rod through body. Styles with luggage rack arms.
Front Door weatherstrip
p/n: 90-1822-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Rear window division bar seal
p/n: 70-0475-82
Pad/Gasket set, back window division bar mounting. Set of four (4) pads, inner and outer, for two (2) dividers. Three fourths (3/4) inch wide.
Brake vacuum cylinder rod boot
p/n: 30-0115-24
Boot, vacuum brake cylinder main rod. Accordion type, two (2) inches diameter by six (6) inches. Top quality workmanship and material.Length: 6.0 inches.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Shock and stabilizer seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.Width: 1.1875 inches.
Motor Mount
p/n: 70-0244-48
Motor mount pad. Cloth base as original, low type, two (2) inches outside diameter by seven eighths (7/8) inch thick.
Cadillac V-8 pedal pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Hood vent bumper
p/n: 33-0053-42
Bumper, hood ventilator door, self retaining. Five sixteenths (5/16) inch diameter, forty eight (48) piece set.
Ride regulator control grommet
p/n: 70-0639-33
Grommets, ride regulator control rod through fender splash shield. Two (2) per car. Made without rod hole. You cut rod slot as required at installation.
Brake vacuum cylinder rod boot
p/n: 70-0485-24
Boot, brake vacuum cylinder rod, for piston type vacuum cylinder.
Carpet heel plate
p/n: 70-0617-88
Heel mat, front carpet insert.Length: 13.5625 inches. Width: 9.75 inches.
Gearshift grommet
p/n: 70-0334-26
Shield, gearshift through floorboard, molded in all detail, including bolt holes.Length: 7.5 inches. Width: 5.875 inches.
Luggage Rack Grommet
p/n: 70-0403-46
Grommets, luggage rack arms through sheet metal, special tall type.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Filler neck extension pad
p/n: 70-0123-41
Mounting pad, filler neck extension. Four and nine sixteenths (4-9/16) inches diameter, double bead.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Inner Fender Seal
p/n: 60-0288-45
Inner Fender Seal for anti-rattle, runningboard apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Flexible Run Channel
Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Available in 5ft and 6ft lengths.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Rumbleseat step mounting pad
p/n: 70-0043-44
Pad, rumbleseat step mounting for fender, double beaded edge per original.Width: 4.375 inches.
Steering column floorplate
p/n: 70-0340-88
Seal, steering column to toe board. Three fourths (3/4) inch thick, high grade sponge, die cut holes.Length: 3.875 inches. Width: 3.875 inches.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Trunk Weatherstrip
p/n: 70-0798-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.