Search Results
Windshield Gasket
p/n: 50-0530-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit.
Front Door Vent Window Kit
p/n: 90-0333-90
This front door vent window weatherstrip kit is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0001-55
This front door vent window weatherstrip set contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Front bow weatherstrip
p/n: 70-0046-64
Weatherstrip, convertible top front bow-to-windshield with integral end pads.
Ferrule installing tool
p/n: 70-0662-69
Installing tool, door and trunk handle ferrule. For cars and trucks using door and trunk handle ferrules such as our #70-0111-69.
Transmission mounting pad
p/n: 50-0257-25
Pad, transmission support. Special resilient rubber. Use your original channel, plate and cap. One (1) set, (2 pad per set) per car.
Rumbleseat Weatherstrip
p/n: 25-0025-85
This rumbleseat weatherstrip set is designed from original parts for superior fitment and seal. The set contains the pieces for the lower edge and corners.
Trunk Weatherstrip
p/n: 70-1128-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Detachable center post pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.Width: 1.375 inches. Height: .28125 inches.
Fenderskirt edge seal
p/n: 70-0055-45
Seal, fenderskirt edge. Each five (5) foot long. Similar to our #20-0111-44, but thicker.Length: 60.0 inches. Width: .25 inches.
Rumbleseat Weatherstrip
p/n: 70-0166-85
This rumbleseat weatherstrip is designed from the original part for superior fitment and seal. The strip seals the lower edge of the rumbleseat.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Brown brake and clutch pad
p/n: 50-0049-89
Pad, brake and clutch pedal. Brown rubber. For black see our #50-0049-22. Full slip-over type as original.Color:brown Width: 3.0 inches.
Brake and clutch pedal pad
p/n: 50-0049-22
Pad, brake and clutch pedal. Black rubber. For brown see our #50-0049-89. Full slip-over type as original.Width: 3.0 inches. Height: 2.75 inches.
Hood corner pad
p/n: 70-0047-42
Pads, hood corners, rear. Original style with metal core and metal fastening tabs.
Hood corner pad
p/n: 50-0036-42
Pads, hood corners, front. Original type with metal core and retaining tab.Width: 1.625 inches.
Front bumper grommet
p/n: 50-0031-28
Grommets, front bumper. Fully molded rubber. Three and three fourths inch (3-3/4") outside length by two inches (2") outside width by one and five eighths inch (1-5/8") inside hole length by one half inch (1/2") inside hole width by fifteen sixteenths inc
Fuel neck grommet
p/n: 70-0050-39
Grommet, fuel filler neck. Fully duplicates original with large retaining flange. Flexible, molded rubber. Four and one eighth inch (4 1/8") outside diameter by two and three sixteenth inch (2 3/16") inside hole diameter by fifteen sixteenths inch (15/16"
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Cowl Vent Weatherstrip
p/n: 70-0224-54
Weatherstrip, cowl vent. Original solid rubber configuration, not a sponge substitute. A top quality part for your classic vehicle restoration.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Rumbleseat step mounting pad
p/n: 70-0043-44
Pad, rumbleseat step mounting for fender, double beaded edge per original.Width: 4.375 inches.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Radio antenna end loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on runningboard on some models.
Side mount cover pad
p/n: 70-0077-37
Pads, channel type, for sidemount covers. Eight (8) piece set.Width: .25 inches. Height: .6875 inches.
Rumbleseat lid corner pad
p/n: 70-0048-87
Pads, rumbleseat lid corners original style, rounded triangular shape.Width: 1.25 inches.
5" Wide Bowdrill Cloth Tape
p/n: 70-1175-65
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Windshield division bar gasket
p/n: 70-0059-51
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Firewall grommet
p/n: 50-0396-20
Grommet, firewall for wiring harness and other usage.Width: 2.0 inches. Height: 1.4375 inches.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
2-1/2" Bowdrill Cloth Tape
p/n: 70-1172-65
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
Door handle ferrule
p/n: 70-0111-69
Ferrule, for three fourths (3/4) inch outside door handle. Chrome plated brass. (See #70-0009-69 for grommet). Used for outside door handle or outside trunk handle.
Vent Window Division Bar Weatherstrip
p/n: 70-0040-56
Vent window division post seal. Extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Wiper transmission gasket
p/n: 70-1196-53
Mounting gasket, windshield wiper transmission.Width: 2.5 inches.
2-1/2" Tan Bowdrill Cloth Tape
p/n: 70-1173-65
Tan bowdrill cloth tape is used for covering convertible side window weatherstrip.