Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
This Rear Leaf Spring Bushing pair is designed from the original part for superior fitment and function. Busing are for the rear leaf spring front or rear spring eyes.
This Firewall Grommet is used on the lower end of the elbow from the firewall to the voltage regulator. Designed from the original part for superior fit and seal.
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Boot, running board antenna wire connection.
Pads, channel type, for sidemount covers. Eight (8) piece set.Width: .25 inches. Height: .6875 inches.
Pads, rumbleseat lid corners original style, rounded triangular shape.Width: 1.25 inches.
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
Boot, starter solenoid.
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Grommet, exhaust system support bracket.
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
This four (4) piece Trunk Hinge Mounting Pad is designed from the original part for superior fitment and function. The installed length is 5-1/2" inches.
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
This Vent Window Division Bar Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
This Windshield Wiper Transmission Gasket pair is designed from the original part for superior fitment and function. This gasket mounts between the windshield wiper transmission and the vehicle body work to reduce noise and vibration.
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped. Three inches (3") length by two inches (2") width by fifteen sixteenths inch (15/16") locating collar outside diameter by one half inch (1/2") inside hole diameter. Three ei
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car. One and one fourth inch (1 1/4") outside diameter by one half inch (1/2") inside hole diameter by seven eighths inch (7/8") height. Used as a f
Bushing, rear stabilizer ends. Four (4) required per car. Fully molded rubber. One and one eighths inch (1 1/8") top outside diameter by seven eighths inch (7/8") bottom outside diameter by nine sixteenths inch (9/16") inside hole diameter by one and one
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Pad, body mounting. Fully molded rubber with locating collar. Two inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter. Three eights inch (3/8") square base height b
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Pad, door side bumper. Clip retained.
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Pad, side window lower rest. Two (2) per window.
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
This Body To Frame Mounting Pad is designed from the original parts for superior fitment and function. Installs under body mount / washer below bracket. Fully molded high quality EPDM rubber.
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Grommet, for outside door handle ferrule (our #70-0111-69, ordered separately). Molded rubber with cloth covering per original.
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Typically used for wiring.
This Masticated Rubber Sheet is three thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
Pad, door check link. For rod type door check. One (1) inch diameter by three eighths (3/8) inch thick with five sixteenths (5/16) inch hole.
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
This two (2) inch long Brake Cable Shielding Cover is designed install for an authentic fit, finish and function. Fits all models with seven sixteenths (7/16) inch outside diameter cable.
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.