Search Results
Running Board Matting
p/n: 30-0218-49
Running board matting for Model 115C only. Made from the molded running board matting for the 120's (our #30-0214-49).
Suspension bushing
p/n: 30-0386-36
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Motor mount service
p/n: 30-0360-11
Support assembly, rear motor mount. Revulcanization service only.
Front suspension bumper
p/n: 30-0228-32
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Front Door Vent Window Weatherstrips
p/n: 30-0098-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts but both strips need to be cut in to three (3) sections to facilitate installation.
Front spring bushing
p/n: 30-0393-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Side roof rail weatherstrip
p/n: 30-0031-65
Weatherstrip, side window. Fits metal channel. Rubber only. Twelve (12) foot strip.Length: 144.0 inches. Width: .75 inches.
Transmission stabilizer
p/n: 30-0252-24
Stabilizer, fore and aft transmission to frame. A factory service part used to remedy clutch chatter. Steel core as original.Length: 7.50 inches.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Door Lock Striker Revulcanization Service
p/n: 30-0398-71
This Revulcanization Service Only is to restore your front or rear Door Lock Striker to it's like new original condition. Service requires your old metal striker core. Please call or email for more service details and ordering.
Front spring bumper
p/n: 30-0227-32
Bumper assembly, front spring rebound (upper arm). Steel core, with treaded stud just like original.
Door weatherstrip
p/n: 30-0085-73
Weatherstrip, door, hollow bulb seal construction to replace composite sponge and solid rubber. Retained by metal clips (not included, see our #70-0391-73).
Axle rebound pad
p/n: 30-0054-32
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Rear bumper grommet
p/n: 30-0078-29
Grommets, rear bumper. Molded left and right as original with excellent detailing. Fully molded rubber with retaining flange. Three and three fourths inch (3-3/4') outside length by three and eleven sixteenths inch (3-11/16") width by one and seven eighth
Gearshift boot
p/n: 30-0178-24
Boot, gearshift cover. For cane shifts only.Length: 4.0 inches. Width: 3.0 inches. Height: 5.125 inches.
Rear bumper grommet
p/n: 30-0197-29
Grommets, rear bumper. Molded left and right. Fully molded rubber. Four and one eighths inch (4-1/8") outside length by three and three fourths inch (3-3/4") outside width by seven eighths inch (7/8") height.
Front bumper grommet
p/n: 30-0077-28
Grommets, front bumper. Molded right and left, including retaining flange. Fully molded rubber. Three and fifteen sixteenths inch (3-15/16") outside length by two and five eighths inch (2-5/8") outside width by one and one half inch (1-1/2") inside hole l
Accelerator pedal service
p/n: 30-0400-41
Pedal, accelerator. Revulcanization service only. Includes new ball sockets as original, with correctly detailed tread pattern.Length: 9.625 inches.
Taillight Mounting Pad
p/n: 30-0231-15
Gaskets, taillight mounting. Length: 4.625 inches. Width: 2.1875 inches.
Motor mount pad
p/n: 30-0238-11
Cushions, motor support, at timing gear cover. One (1) pair required per car. Sold only in pairs.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16 Bead - 50 Ft. Roll
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Red brake and clutch pedal pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Brake and clutch pedal pad
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Radiator mounting pad
p/n: 30-0208-31
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Cowl vent gasket
p/n: 30-0179-54
Gasket, cowl vent, original labyrinth type, not sponge.Length: 14.75 inches. Width: 5.50 inches.
Beltline Weatherstrip
p/n: 70-0555-58
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Brake and clutch shank seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting with 3/16 Bead - 25 Ft. Roll
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Shock absorber bushing
p/n: 30-0024-33
Bushings, rear shock link assembly. Designed to act like sleeve inside link arm.Height: .9375 inches.
5" Wide Bowdrill Cloth Tape
p/n: 70-1175-65
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
Taillight lens gasket
p/n: 30-0336-15
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Shock absorber bushing
p/n: 30-0226-33
Bushings, rear shock link, upper. Rubber sleeve construction like original.
Electrical terminal boot
p/n: 30-0279-41
Boot, electrical connection, generator terminal or ignition coil at engine.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Door bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
2-1/2" Bowdrill Cloth Tape
p/n: 70-1172-65
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
