Please click on the part name in red in order to get a complete description.
Motor mount, rear at bell housing. Revulcanization service only.
This eight (8) piece kit includes the inner and outer windowfelts, upper rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door. Models with wood in the doors use our #70-1168-58 as lower rigid run channel.
Weatherstrip, quarter window vent.
Front door weatherstrip. This set is the primary seal for the door to the body. Set includes the door perimeter weatherstrip and the door bottom weatherstrip. Enough for two (2) doors. Includes fasteners.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This six (6) piece kit includes the inner and outer windowfelts and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models without vent windows in the door.
Motor mount, front, upper or lower, as required. Revulcanization service only.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
This rear window gasket set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Grommets, rear bumper. Hollow construction for good fit. Fully molded rubber with locating tabs. Four and three eighths inch (4-3/8") outside length by two and three fourths inch (2-3/4") outside width by one and three fourths inch (1-3/4") inside hole le
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Bumper, rear spring, right and left.
Transmission support pad, insulator blocks, upper and lower.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Seal, fenderskirt edge. Each five (5) foot long. Similar to our #20-0111-44, but thicker.Length: 60.0 inches. Width: .25 inches.
Retainer, front floor mat on steering column (also called steering column floorplate). Brown rubber. For black see our #50-0260-36.
Gasket, windshield division post, inner and outer, also acts as retainer for outer division bar chrome, molding.
Bumper, front suspension, lower arm.Width: 2.625 inches. Height: 2.5625 inches.
Grommets, front bumper, right and left. Fully molded rubber. Four and three fourths inch (4-3/4") outside length by three inches (3") outside width by one and five eighths inch (1-5/8") inside hole length by one half inch (1/2") inside hole width by one a
Kit, stabilizer bar link assembly. Twenty two (22) piece set for both sides of one (1) car, front and rear. (Order 2 sets if you need both). Hex head bolt. 5/16"-24nf x 7-5/8" lg. Comes with metal sleeve, cup washers and rubber grommets.
Front Spring Rubber Bumper - for upper control arm on frame.
Bushing, stabilizer bracket. Constructed of durable BUNA rubber. One and five eighths inch (1 5/8") length by one and one half inch (1 1/2") outside diameter by three fourths inch (3/4") inside hole diameter.
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Right and left taillight mount pad. Replaces #1304392-3, excellent job, fully detailed.
Pad, accelerator pedal. Rubber flanges all around as original to fit over pedal core.Length: 9.125 inches.
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Retainer, front floor mat on steering column (also called steering column floorplate). Black rubber. For brown see our #50-0260-89.Width: 4.3125 inches.
Window run channel with stainless beaded edge. Six (6) foot length. Cloth covered, mohair lined, flexible channel for sides and top of door windows. Exact replacement for listed vehicles but can be used in many applications.
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Cover, automatic choke cable at carburetor.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Pad, parking light (fender light).Width: 8.75 inches.
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Mounting pads, trunk hinge, four (4) piece set. Models with outside hinges.Length: 8.25 inches.
Pad, brake and clutch pedal. Brown rubber. For black see our part #50-0054-22. Perfect copy, fine detail.Color:brown Width: 3.125 inches.
Window run channel, stainless beaded edge. Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Perfect dimensions, Five eighths (5/8) inch wide by nine sixteenths (9/16) inch overall height, exact replacement. Five (5) fo
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Weatherstrip, inner and outer for sliding quarter window, chrome beaded, mohair faced, flexible stock. May be formed to required outline. Six (6) foot strip.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Mounting pad, rumbleseat step to fender, proper beaded edge, exact copy.Width: 4.8125 inches.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on runningboard on some models.
Boot, runningboard antenna wire connection.
Pad, rear license light and trunk handle body.Length: 7.50 inches.
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Pad, brake and clutch pedal. Black rubber. For brown see our part #50-0054-89. Perfect copy, fine detail.Width: 3.125 inches. Height: 2.125 inches.
Boot, starter solenoid.
Grommet, wire harness-thru-firewall mat. Two (2) inch diameter with two and one fourth (2-1/4) inch outside diameter flange.
Boot, battery cable at starter solenoid.Width: 2.75 inches.
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Pad, body mounting. Fully molded rubber with locating collar. Two and one fourth inch (2 1/4") square by one and one fourth inch (1 1/4") locating collar outside diameter by seven sixteenths inch (7/16") locating collar inside hole diameter. Three eighths
Shim, body sill.. Fully molded rubber, rectangular shaped. Two and one half inch (2 1/2") length by one and seven eighths inch (1 7/8") width by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height. Buick useage for bolt location
Shim, body sill. Fully molded rectangular rubber. A total of six (6) are needed per car. Three inches (3") length by one and eleven sixteenths (1 11/16") width by one half inch (1/2") inside hole diameter by three eighths inch (3/8") height. Buick useag
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Grommet, two (2) holes for oil pressure and water temperature lines through firewall.
Gasket, windshield wiper transmission. Replaces #4074294 & #4082366.
Gravel shield, front bumper, anti-rattle.
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Grommet, dimmer switch for carpet application.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car. One and one fourth inch (1 1/4") top outside diameter by one and one eighth inch (1 1/8") bottom outside diameter by five eighths inch (5/8") inside hole diameter by t
Channel, side window, pre-flocked, five sixteenths (5/16) inch wide base for one fourth (1/4) inch glass. Most Fisher closed bodies except those using stainless beaded channel. For nine sixteenths (9/16) inch wide channel, see our #70-1169-58.
Lacing, hood, fabric, webbing anti-squeak. DOES NOT have hollow center. Fasten with rivets if so found originally. Excellent quality.
Lacing, hood, fabric, webbing anti-squeak. With hollow center to receive wire if needed, or fasten with rivets if so found originally. Excellent quality. Seven eighths (7/8) inch by one eighths (1/8) inch thick.
Bumper, front and rear body hinge pillar, one (1) inch diameter by one fourth (1/4) inch thick, held by screw, steel core. Auxiliary, used only where needed to prevent door rattle.Note: also used on 1942-50 Packards with Clipper styling near t
Mounting pad. Two and one fourth (2-1/4) inches outside diameter by five eighths (5/8) inch inside diameter by one half (1/2) inch thick.
Dust cover, tie rod ends.
Rubber washer, door check link stop.
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Anti-rattle roller, side windows. Rubber only, replaces original perfectly and easily. Fits both styles of brackets.
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Knob for inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. See also our #70-0660-70.
Grommet, shock and stabilizer link. Eight (8) required per car. Fully molded rubber with locating collar. One and one sixteenth inch (1 1/16") outside diameter by nine sixteenths inch (9/16") locating collar outside diameter by three eighths inch (3/8") i
Pad, door check link. For rod type door check. One (1) inch diameter by three eighths (3/8) inch thick with five sixteenths (5/16) inch hole.
End plug, swing-type sun visor tube. Brown only.
Anti-rub cover, brake cable. Fits all models with seven sixteenths (7/16) inch outside diameter cable.Width: 2.0 inches.
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel.Width: .375 inches. Height: .6875 inches.
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Seal, door bottom, held by metal track or by clips. (See our # 70-0391-73 for clips). 2 door styles need about seven (7) foot per car.
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).Width: .75 inches. Height: .
Channel, windshield, for windows without chrome reveal molding. (With 2 piece windshield, select gasket for division bar).
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel.Width: .375 inches. Height: .
Gasket, window, for models with chrome reveal molding.
Gasket, window, for models without chrome reveal molding.
Seal, steering knuckle support, upper or lower. Die cut one fourth (1/4) inch, four (4) used per car.Height: .25 inches.
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on