Search Results
Front Door weatherstrip
p/n: 90-0102-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Motor mount
p/n: 70-0965-11
Motor mount, rear at transmission. Upper and lower cushions with metal washers molded in.
Front Door Vent Window Kit
p/n: 90-0446-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0006-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 70-0601-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Windshield Gasket
p/n: 70-1785-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Front bow weatherstrip
p/n: 70-0138-64
Weatherstrip, front bow-to-windshield, outer, right and left, molded with end hook, screw holes and clearances.Length: 27.0 inches.
Front bow weatherstrip
p/n: 70-0157-64
Weatherstrip, front bow-to-windshield, inner, right and left, superior copy.Length: 25.0 inches.
Door weatherstrip
p/n: 70-0085-73
Weatherstrip, door opening, fits retainer under edge of body sill to form seal when door is closed. Six (6) foot strips.Length: 72.0 inches. Width: 1.
Trunk Weatherstrip
p/n: 70-0796-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
LaSalle monogram pedal pad
p/n: 70-0037-22
LaSalle pedal pads, clutch and brake, excellent copy from authentic original with LaSalle monogram.
Hood ventilator wedge pad
p/n: 70-0317-42
Wedge pads, hood side ventilators. Fourteen (14) piece set.
Rear bumper grommet
p/n: 70-0144-29
Grommets, rear bumper (Some cars have this type, some have our #70-0164-29, sold separately. They are both interchangeable and original). Fully molded rubber. Five inches (5") outside length by three and one eighths inch (3-1/8") outside width by one and
Bumper grommet
p/n: 70-0102-28
Grommets, bumper arm. Fully molded rubber. Five inches (5") outside length by three and one sixteenths inch (3-1/16") outside width by one and five eighths inch (1-5/8") inside hole length by one half inch (1/2") inside width by one and one half inch (1-1
Taillight mounting pad
p/n: 70-0316-15
Pads, taillight mounting, right and left, top grade workmanship and material.
Detachable center post pad
p/n: 70-0279-67
Pads, for bottom of folding post or body, brass core as original, screw held.Length: 1.875 inches. Width: 1.0625 inches.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Rear bumper grommet
p/n: 70-0164-29
Grommets, rear bumper. (Some cars have this type, some have our #70-0144-29, sold separately. They are both interchangeable and original). Fully molded rubber. Four inches (4") outside length by two and one eighths inch (2-1/8") outside width by one and f
Detachable center post pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.Width: 1.375 inches. Height: .28125 inches.
Hinge post weatherstrip
p/n: 70-0383-73
Weatherstrip, hinge post at instrument panel. Steel inserts at holes
Fenderskirt edge seal
p/n: 70-0055-45
Seal, fenderskirt edge. Each five (5) foot long. Similar to our #20-0111-44, but thicker.Length: 60.0 inches. Width: .25 inches.
Rumbleseat Weatherstrip
p/n: 70-0282-85
These rumbleseat weatherstrips are designed from the original part for superior fitment and seal. The pieces are molded as left and right for the lower corners.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Windshield division bar gasket
p/n: 70-0159-51
Gasket, windshield division post, inner and outer, also acts as retainer for outer division bar chrome, molding.
Carpet heel plate
p/n: 70-0604-88
Heel mat, front carpet, driver's position.Length: 15.75 inches. Width: 6.25 inches.
Rear stabilizer bushing
p/n: 70-0406-33
Bushings, rear stabilizer. Comes as a four (4) piece set. Fully molded rubber. One and one half inch (1 1/2') top outside diameter by one and five eighths inch (1 5/8") bottom outside diameter by three fourths inch (3/4") inside hole diameter by three fou
Door bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Fenderskirt edge seal
p/n: 20-0111-44
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Front stabilizer bushing
p/n: 70-0717-33
Bushing, front stabilizer bar to frame.Length: 1.875 inches. Width: .6875 inches. Height: 1.625 inches.
Handbrake pull rubber grip
p/n: 70-0385-24
Rubber grip, handbrake pull. This was an optional item alternating with a chrome handle.
Accelerator pedal pad
p/n: 70-0275-40
Pad, accelerator pedal, full slipover type, fits over old metal after removing original rubber.Length: 8.5 inches.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Fuel neck grommet
p/n: 50-0067-39
Grommet, fuel filler neck. Oblong fully molded rubber. Two and one eighths inch (2 1/8") inch inside length by three and one half inch (3 1/2") outside diameter by three and three fourths inch (3 3/4") outside length.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Beltline Weatherstrip
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair and 6ft piece.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Rumbleseat lid bumper pad
p/n: 70-0278-87
Side pads, rumbleseat lid, right and left.Length: 1.125 inches. Width: .6875 inches.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
