Search Results
Please click on the part name in red in order to get a complete description.
Vibration damper service
p/n: 70-0638-12
Vibration damper (harmonic balancer), on front of crankshaft. May need rebalancing upon receipt.
Fender light pad
p/n: 70-0684-16
Mounting pad, fender parking light. Two (2) per car.Length: 17.0 inches.
Fluted radiator hose
p/n: 70-0603-31
Hose, cylinder head to radiator, upper. Fluted as original.Length: 10.125 inches.
Front spring bumper
p/n: 70-0339-32
Bumper, front spring, upper arm on frame. Rubber with heavy steel core, including five sixteenths (5/16) inch stud.
Steering column floorplate
p/n: 70-0683-88
Cover or seal, rubber, steering column and column gearshift at toe board, under carpet.Length: 12.25 inches.
Motor Mount
p/n: 70-0529-11
Front motor mount. Revulcanizing core exchange only. Send your cores when ordering.
Front Door Vent Window Kit
p/n: 90-0335-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Motor mount
p/n: 70-0965-11
Motor mount, rear at transmission. Upper and lower cushions with metal washers molded in.
Front Door Vent Window Weatherstrips
p/n: 38-0003-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Rear window division bar seal
p/n: 70-1453-82
Pads, back window divider, inner and outer. Four (4) piece set of molded rubber for two (2) division bars.
Taillight mounting pad
p/n: 70-0108-15
Pad set, taillight mounting, right and left. Four (4) piece set.
Front bow weatherstrip
p/n: 70-0138-64
Weatherstrip, front bow-to-windshield, outer, right and left, molded with end hook, screw holes and clearances.Length: 27.0 inches.
Door weatherstrip
p/n: 70-0085-73
Weatherstrip, door opening, fits retainer under edge of body sill to form seal when door is closed. Six (6) foot strips.Length: 72.0 inches. Width: 1.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Bumper grommet
p/n: 70-0102-28
Grommets, bumper arm. Fully molded rubber. Five inches (5") outside length by three and one sixteenths inch (3-1/16") outside width by one and five eighths inch (1-5/8") inside hole length by one half inch (1/2") inside width by one and one half inch (1-1
Detachable center post pad
p/n: 70-0279-67
Pads, for bottom of folding post or body, brass core as original, screw held.Length: 1.875 inches. Width: 1.0625 inches.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Detachable center post pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.Width: 1.375 inches. Height: .28125 inches.
Fenderskirt edge seal
p/n: 70-0055-45
Seal, fenderskirt edge. Each five (5) foot long. Similar to our #20-0111-44, but thicker.Length: 60.0 inches. Width: .25 inches.
Rumbleseat Weatherstrip
p/n: 70-0282-85
These rumbleseat weatherstrips are designed from the original part for superior fitment and seal. The pieces are molded as left and right for the lower corners.
Windshield division bar gasket
p/n: 70-0159-51
Gasket, windshield division post, inner and outer, also acts as retainer for outer division bar chrome, molding.
Carpet heel plate
p/n: 70-0604-88
Heel mat, front carpet, driver's position.Length: 15.75 inches. Width: 6.25 inches.
Rear stabilizer bushing
p/n: 70-0406-33
Bushings, rear stabilizer. Comes as a four (4) piece set. Fully molded rubber. One and one half inch (1 1/2') top outside diameter by one and five eighths inch (1 5/8") bottom outside diameter by three fourths inch (3/4") inside hole diameter by three fou
Door bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Fenderskirt edge seal
p/n: 20-0111-44
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Handbrake pull rubber grip
p/n: 70-0385-24
Rubber grip, handbrake pull. This was an optional item alternating with a chrome handle.
Accelerator pedal pad
p/n: 70-0275-40
Pad, accelerator pedal, full slipover type, fits over old metal after removing original rubber.Length: 8.5 inches.
Fuel neck grommet
p/n: 70-0091-39
Grommet, fuel filler neck. Saddle style. Three and three eighths inch (3 3/8") outside width by three and five eighths inch (3 5/8") outside length by two and one fourth inch (2 1/4") inside hole diameter by one and one fourth inch (1 1/4") height.
Rigid Run Channel
p/n: 70-0347-58
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Beltline weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender welting 3/16 bead 25ft
p/n: 70-1099-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Wiring grommet
p/n: 70-0709-21
Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
Rumbleseat lid corner pad
p/n: 70-0152-87
Pads, rumbleseat lid corners, original rounded triangle shape.Length: 1.5 inches. Width: .4375 inches.
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Motor mount
p/n: 70-0648-11
Cushion, motor rear support bracket at transmission, upper and lower. Two (2) or four (4) required per car.Length: 3.125 inches. Width: 1.5625 inches.
Firewall grommet
p/n: 70-0622-20
Grommet, firewall wire harness, oil pressure tube, windshield wiper tube, capillary tube, radio antenna wire.
Firewall grommet
p/n: 70-0621-20
Grommet, firewall, for cowl vent drain hose and throttle control cable.
Bowdrill cloth tape
p/n: 70-1175-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Five (5) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our #70-1170-99 or
Firewall grommet
p/n: 70-1203-20
Grommet, firewall. Four and one eighth (4-1/8) inches long type for various electrical and dash gauges. Also see our #32-1201-20 and #32-0225-20.
Taillight lens gasket
p/n: 70-0652-15
Gasket, taillight lens.Length: 4.75 inches. Width: 3.25 inches.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Spare tire bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Spare tire bumper
p/n: 70-0125-37
Rest pad, spare wheel cover, metal core, tab held type. Sixteen (16) required per car.Width: 1.75 inches. Height: .75 inches.
Glovebox door check grommet
p/n: 70-0285-88
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Bowdrill cloth tape
p/n: 70-1172-65
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our
Vent Window Division Bar Weatherstrip
p/n: 70-0040-56
Vent window division post seal. Extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Tan bowdrill cloth tape
p/n: 70-1173-65
Tape, brown (tan) bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Two and one half (2-1/2) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such
Lower suspension arm dust seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Door check link rod end stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Stabilizer grommet
p/n: 70-0436-33
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car. One and one fourth inch (1 1/4") outside diameter by one half inch (1/2") inside hole diameter by seven eighths inch (7/8") height. Used as a f
Shock and stabilizer bushing
p/n: 50-0220-32
Bushing, for shock absorber link cross pin or stabilizer link cross pin.1931-36 Bushing, rubber, for shock absorber link cross pin, #41151.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Shift lever grommet
p/n: 70-0769-26
Grommet, upper shift lever at steering column.Height: .25 inches.
Firewall grommet
p/n: 70-0712-20
Grommet, firewall for one (1-1/16) inch hole in sheet metal. Two (2) holes in grommet.
Fabric hood lacing
p/n: 70-2221-42
Lacing, hood, fabric, webbing anti-squeak. DOES NOT have hollow center. Fasten with rivets if so found originally. Excellent quality.
Fabric hood lacing
p/n: 60-0578-42
Lacing, hood, fabric, webbing anti-squeak. With hollow center to receive wire if needed, or fasten with rivets if so found originally. Excellent quality. Seven eighths (7/8) inch by one eighths (1/8) inch thick.
Firewall grommet
p/n: 32-0225-20
Grommet, wire harness through firewall. Sheet Metal Hole: 1-1/2" Center Hole: 11/16" Outside Diameter: 2-1/4" Slot Width: 3/32"
Body mounting pad
p/n: 70-0264-48
Cushion, body bolts under washer below bracket. Fully molded rubber. One and one half inch (1 1/2") inch outside diameter by seventeen thirty seconds inch (17/32") inside hole diameter by one fourth inch (1/4") height.
Side window roller
p/n: 70-0117-62
Anti-rattle roller, side windows. Rubber only, replaces original perfectly and easily. Fits both styles of brackets.
Firewall grommet
p/n: 32-0226-20
Grommet, firewall, for handbrake cable. Sheet Metal Hole: 1-1/8" Center Hole: 3/8" Outside Diameter: 1-9/16" Slot Width: 3/32"
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Brown door lock knob
p/n: 70-0660-70
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Firewall grommet
p/n: 32-1201-20
Grommet, firewall. Used for wiring. Sheet Metal Hole: 1-3/32" Center Hole: 9/16" Outside Diameter: 1-9/16" Slot Width: 3/32"
Steering knuckle support seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Run channel mohair liner
p/n: 70-2863-58
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
Brown door lock knob
p/n: 70-0354-70
Knob for inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. See also our #70-0660-70.
Door check link rod end stop
p/n: 70-0325-70
Pad, door check link. For rod type door check. One (1) inch diameter by three eighths (3/8) inch thick with five sixteenths (5/16) inch hole.
Brake cable anti-rub cover
p/n: 70-1701-24
Anti-rub cover, brake cable. Fits all models with seven sixteenths (7/16) inch outside diameter cable.Width: 2.0 inches.
Door Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 70-0411-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Pressure ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel.Width: .375 inches. Height: .6875 inches.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Body hole plug
p/n: 35-0863-45
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.