Search Results
Suspension bushing
p/n: 30-0386-36
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Motor mount service
p/n: 30-0375-11
Insulator assembly, rear engine support at transmission housing. Revulcanization service only.
Windshield Gasket
p/n: 30-0281-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 30-0018-55
This four (4) piece Front Door Vent Window Weatherstrips contain the upper and lower seals that cover the top, front, and bottom of the vent window. All of the pieces are designed from original parts for a precise, factory fit.
Front suspension bumper
p/n: 30-0228-32
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Front spring bushing
p/n: 30-0393-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Side roof rail weatherstrip
p/n: 30-0031-65
Weatherstrip, side window. Fits metal channel. Rubber only. Twelve (12) foot strip.Length: 144.0 inches. Width: .75 inches.
Transmission stabilizer
p/n: 30-0252-24
Stabilizer, fore and aft transmission to frame. A factory service part used to remedy clutch chatter. Steel core as original.Length: 7.50 inches.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Door Lock Striker Revulcanization Service
p/n: 30-0398-71
This Revulcanization Service Only is to restore your front or rear Door Lock Striker to it's like new original condition. Service requires your old metal striker core. Please call or email for more service details and ordering.
Front spring bumper
p/n: 30-0227-32
Bumper assembly, front spring rebound (upper arm). Steel core, with treaded stud just like original.
Detachable center post pad
p/n: 30-0423-67
Pad, convertible top right and left latches.Width: 3.0 inches. Height: 2.50 inches.
Hood corner pad
p/n: 30-0011-42
Pads, hood front corners, large type. Molded right and left with metal cores and double tab retainers.Length: 3.1875 inches. Width: 2.125 inches.
Door Weatherstrip
p/n: 30-0051-73
Weatherstrip, door edge. Retained by metal clips. (For clips, see our #70-0391-73). Fifteen (15) feet per strip.
Axle rebound pad
p/n: 30-0371-32
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Gearshift boot
p/n: 30-0178-24
Boot, gearshift cover. For cane shifts only.Length: 4.0 inches. Width: 3.0 inches. Height: 5.125 inches.
Hood corner pad
p/n: 30-0010-42
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Accelerator pedal service
p/n: 30-0400-41
Pedal, accelerator. Revulcanization service only. Includes new ball sockets as original, with correctly detailed tread pattern.Length: 9.625 inches.
Rear bumper grommet
p/n: 30-0067-29
Grommets, rear bumper.Length: 4.3125 inches. Width: 2.6875 inches.
Motor mount pad
p/n: 30-0238-11
Cushions, motor support, at timing gear cover. One (1) pair required per car. Sold only in pairs.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16 Bead - 50 Ft. Roll
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Red brake and clutch pedal pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Bumper grommet
p/n: 30-0039-28
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumper grommets. Three and five eighths inch (3-5/8") outside length by two and one fourth inch (2-1/4") outside width by one and five eighths
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Brake and clutch pedal pad
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Convertible post bumper
p/n: 70-2155-67
Bumper, convertible top pillar. Fully molded out of rubber.Width: 1.0 inches. Height: 2.0625 inches.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Taillight mounting pad
p/n: 30-0318-15
Gaskets, taillight mounting, with proper beading and shape as original. For all models with center license mounting.Length: 7.125 inches.
Cowl vent gasket
p/n: 30-0050-54
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Firewall grommet
p/n: 30-0070-21
Grommet instrument board cables through firewall. Oval type with masked hole for six (6) wires or cables. Necessary replacement for correct restoration.
Beltline Weatherstrip
p/n: 70-0555-58
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Windshield filler
p/n: 30-0105-52
Filler, windshield division channel ends, upper and lower. Two (2) piece set.
Brake and clutch shank seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting with 3/16 Bead - 25 Ft. Roll
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Detachable center post pad
p/n: 30-0422-67
Pad, convertible top center latch. Excellent workmanship with metal insert like originalWidth: 2.0 inches. Height: 1.1875 inches.
5" Wide Bowdrill Cloth Tape
p/n: 70-1175-65
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
Taillight lens gasket
p/n: 30-0336-15
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Lock cylinder gasket
p/n: 30-0389-71
Gasket, door lock handle escutcheon, front and rear doors. Two (2) or four (4) required per car.
Electrical terminal boot
p/n: 30-0279-41
Boot, electrical connection, generator terminal or ignition coil at engine.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
2-1/2" Bowdrill Cloth Tape
p/n: 70-1172-65
Bowdrill cloth tape is used for covering convertible side window weatherstrip. Available in a 5 ft roll.
