Search Results
Front spring bumper
p/n: 70-0339-32
Bumper, front spring, upper arm on frame. Rubber with heavy steel core, including five sixteenths (5/16) inch stud.
Taillight mounting pad
p/n: 70-0108-15
Pad set, taillight mounting, right and left. Four (4) piece set.
Door weatherstrip
p/n: 70-0085-73
Weatherstrip, door opening, fits retainer under edge of body sill to form seal when door is closed. Six (6) foot strips.Length: 72.0 inches. Width: 1.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Lower Suspension Arm Dust Seal Set
p/n: 70-0865-32
This four (4) piece Lower Suspension Arm Dust Seal Set is fully molded of high-quality EPDM dense rubber for durability and proper fitment. These seals are used to protect your lower suspension arm bushings from dust and debris.
Cadillac V-8 pedal pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Front bumper grommet
p/n: 70-0291-28
Grommets, front bumper arm. Hollow construction for good fit. Fully molded rubber. Four and seven eighths inch (4-7/8") outside length by two and five eighths inch (2-5/8") outside width by one and five eighths inch (1-5/8") inside hole length by nine six
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16 Bead - 50 Ft. Roll
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Windshield division bar gasket
p/n: 70-0247-51
Gasket set, windshield divider post, inner and outer. Two (2) piece set with screw holes and pilots.
Rear stabilizer bushing
p/n: 70-0406-33
Bushings, rear stabilizer. Comes as a four (4) piece set. Fully molded rubber. One and one half inch (1 1/2') top outside diameter by one and five eighths inch (1 5/8") bottom outside diameter by three fourths inch (3/4") inside hole diameter by three fou
Fender Skirt Edge Weatherstrips
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Accelerator pedal pad
p/n: 70-0275-40
Pad, accelerator pedal, full slipover type, fits over old metal after removing original rubber.Length: 8.5 inches.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Rigid Run Channel
p/n: 70-0347-58
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
License plate mounting pad
p/n: 70-0124-17
Pad, rear license bracket mounting. See our other parts #70-0174-17 and #70-0348-17 sold separately.
Fender welting 1/4" bead 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Fender welting 25ft chrome
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft lengths.
Fender Welting with 3/16 Bead - 25 Ft. Roll
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Side Window Sash Channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Rear Engine Mount
p/n: 70-0648-11
This Rear Engine Mount is used as an upper and lower support bracket at the transmission. Made from high-quality EPDM rubber for a precise, factory like fit.
Firewall grommet
p/n: 70-1203-20
Grommet, firewall. Four and one eighth (4-1/8) inches long type for various electrical and dash gauges. Also see our #32-1201-20 and #32-0225-20.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Spare tire bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Electrical terminal boot
p/n: 30-0279-41
Boot, electrical connection, generator terminal or ignition coil at engine.
Hood rest pad
p/n: 70-0150-42
Pad, hood rest, molded to brass core, screw mounted.Width: 1.75 inches.
Spare tire bumper
p/n: 70-0125-37
Rest pad, spare wheel cover, metal core, tab held type. Sixteen (16) required per car.Width: 1.75 inches. Height: .75 inches.
Battery Clamp Cover
p/n: 70-0095-21
This black rubber Battery Clamp Cover helps to protect the nearby metal and finish. Good copy from an original part. Length: 3-1/2" inches.
Door Handle Ferrule
p/n: 60-0389-69
Ferrule, outside door handle. Chrome with rubber sleeve. Two (2) piece set includes one (1) chrome piece and one (1) rubber piece. Enough for one door.
Body mounting pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped. Three inches (3") length by two inches (2") width by fifteen sixteenths inch (15/16") locating collar outside diameter by one half inch (1/2") inside hole diameter. Three ei
Lower suspension arm dust seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Door check link rod end stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Stabilizer grommet
p/n: 70-0436-33
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car. One and one fourth inch (1 1/4") outside diameter by one half inch (1/2") inside hole diameter by seven eighths inch (7/8") height. Used as a f
Shock and stabilizer bushing
p/n: 50-0220-32
Bushing, for shock absorber link cross pin or stabilizer link cross pin.1931-36 Bushing, rubber, for shock absorber link cross pin, #41151.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Body mounting pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter. Three eights inch (3/8") square base height b