Search Results
Please click on the part name in red in order to get a complete description.
Front Door Vent Window Kit
p/n: 90-0364-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Motor mount service
p/n: 27-0038-11
Insulator, engine support rear. Two (2) per car. Revulcanization service only.Length: 4.0 inches.
Windshield Gasket
p/n: 70-1784-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Front Door Vent Window Weatherstrips
p/n: 38-0014-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Door weatherstrip
p/n: 90-0106-72
Door edge weatherstrip. This part is the primary door to body weatherstrip. This includes the seals for the sides and bottom of the door.
Motor mount service
p/n: 27-0037-11
Insulator, engine support, front. One (1) per car. Revulcanization service only.Length: 5.625 inches.
Front bow weatherstrip
p/n: 70-0138-64
Weatherstrip, front bow-to-windshield, outer, right and left, molded with end hook, screw holes and clearances.Length: 27.0 inches.
Front bow weatherstrip
p/n: 70-0157-64
Weatherstrip, front bow-to-windshield, inner, right and left, superior copy.Length: 25.0 inches.
Trunk Weatherstrip
p/n: 70-1128-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Rigid run channel
p/n: 70-0536-58
Run channel, front door window, for full length of division bar (approximately twenty nine (29) inches). Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top.
Accelerator pedal service
p/n: 70-1777-40
Accelerator pedal, black. Revulcanization service only. For brown see our #70-1777-89.Length: 8.1875 inches. Width: 2.0 inches.
Trunk Weatherstrip
p/n: 70-1129-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 3/16 bead 50ft
p/n: 70-1100-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Detachable center post pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.Width: 1.375 inches. Height: .28125 inches.
Axle rebound pad
p/n: 70-0210-32
Bottoming pads, rear axle. Rubber block mounts by bracket to rear axle tube.
Front bumper grommet
p/n: 27-0054-28
Grommet, front bumper. Fully molded rubber, detailed and flanged as original. Four and one fourth inch (4-1/4") outside length by two and seven sixteenths inch (2-7/16") outside width. One and three fourths inch (1-3/4") inside hole length by nine sixteen
Windshield division bar gasket
p/n: 70-0309-51
Gaskets, windshield division channel, inner and outer, fully molded to include bolt holes and pilots. Two (2) piece set.
Front bumper grommet
p/n: 27-0018-28
Grommet, front bumper. Fully detailed and flanged as original. Fully molded rubber. Three and three fourths inch (3-3/4") outside length by two and three sixteenths inch (2-3/16") outside width by one and nine sixteenths inch (1-9/16") inside hole length