Gravel shield, rear fender, right and left hand. Fully molded to original contour with attaching tabs and steel backing plate. Will fit fender contour perfectly without puckering as happens with others made flat. Models without running board.
Bumpers, convertible top detachable pillar, upper and lower, right and left. With metal core per original, four (4) piece set.
Front engine mount. Rubber and steel construction.
Rear body deflector apron or valance. Original copy including fastening bolt holes. You locate exhaust hole where needed. Approximately fifty eight (58) inches long.
This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Gravel shield between body and rear fender, right and left, steel core.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Door edge weatherstrip. This part is the primary door to body weatherstrip and the upper hinge pillar weatherstrip. Adhesive not included in kit.
Cushion support, motor, rear on transmission to cross member. Revulcanization service only. Similar to #70-0674-11.Length: 3.75 inches. Width: 2.25 inches.
Pads, taillight body mounting.
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Bumpers, front spring. Lower arm, original copy, integral molded plate and stud, three eighths (3/8) inch standard thread, for installing.
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
Door edge weatherstrip. Two door seals. Used for the front doors on Chevrolet, Oldsmobile & Pontiac models. Also used for the front or rear doors on Buick models. If needing all four (4) door seals for Buick purchase two (2) pairs. This part is the primar
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Grommets, front bumper arm. Hollow construction for good fit. Fully molded rubber. Four and seven eighths inch (4-7/8") outside length by two and five eighths inch (2-5/8") outside width by one and five eighths inch (1-5/8") inside hole length by nine six
Pads, parking light, excellent copy.
Filler, front door hinge pillar at dash, right and left. With metal core. Located at top front of front door, under door flange.
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Bumper, front spring, upper arm (on frame).
Grommets, rear bumper. Fully molded rubber. Four and one fourths inch (4-1/4") outside length by two and five sixteenths inch (2-5/16") outside width by one and eleven sixteenths inch (1-11/16") inside hole length by nine sixteenths inch (9/16") inside ho
Seal, fenderskirt edge. Each five (5) foot long. Similar to our #20-0111-44, but thicker.Length: 60.0 inches. Width: .25 inches.
Bottoming pads, rear axle. Rubber block mounts by bracket to rear axle tube.
Pad, accelerator pedal. Slipover style. Exact copy and top quality rubber.
Bumper, trunk lower stop, right and left.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Grommet, fuel filler neck. Off center flange style. Fully molded rubber.
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Grommets, clutch and brake pedal shank. Hollow accordion action type, not a sponge ring.
Hose, cowl vent gutter drain.Length: 7.0 inches.
This Convertible Top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Pad, rear license bracket mounting.
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft lengths.
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.