Front engine mount. Rubber and steel construction.
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door.
Rear body deflector apron or valance. Original copy including fastening bolt holes. You locate exhaust hole where needed. Approximately fifty eight (58) inches long.
Bumper, front spring, upper arm on frame. Rubber with heavy steel core, including five sixteenths (5/16) inch stud.
Cover or seal, rubber, steering column and column gearshift at toe board, under carpet.Length: 12.25 inches.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Motor mount, rear at transmission. Upper and lower cushions with metal washers molded in.
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Door weatherstrip. This set is the primary seal for the door to the body. Set contains two (2) seals for either the front or rear doors. Purchase two (2) sets if you need to complete all four (4) doors.
Cushion support, motor, rear on transmission to cross member. Revulcanization service only. Similar to #70-0674-11.Length: 3.75 inches. Width: 2.25 inches.
Spring bumper, rear axle. Fastens to spring clamp.
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Pad, taillight, right and left, matched pair.
Grommets, front or rear bumper. Fully original, hollow construction.
Dust seal, lower suspension arm bushing. Four (4) piece set.
Bumpers, front spring, lower arm.
Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top. Available in 29" pairs.
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Grommets, front bumper arm. Hollow construction for good fit. Fully molded rubber. Four and seven eighths inch (4-7/8") outside length by two and five eighths inch (2-5/8") outside width by one and five eighths inch (1-5/8") inside hole length by nine six
Pads, parking light, excellent copy.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Seal, fenderskirt edge. Each five (5) foot long. Similar to our #20-0111-44, but thicker.Length: 60.0 inches. Width: .25 inches.
Gasket set, windshield divider post, inner and outer. Two (2) piece set with screw holes and pilots.
Pad, accelerator pedal. Slipover style. Exact copy and top quality rubber.
Grommet, steering column at toe board over carpet.
Bushings, rear stabilizer. Comes as a four (4) piece set. Fully molded rubber. One and one half inch (1 1/2') top outside diameter by one and five eighths inch (1 5/8") bottom outside diameter by three fourths inch (3/4") inside hole diameter by three fou
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Bumper, trunk. Brass core, screw held. Two (2) per car.Length: 1.5 inches. Width: .75 inches.
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Grommet, fuel filler neck. Saddle style. Three and three eighths inch (3 3/8") outside width by three and five eighths inch (3 5/8") outside length by two and one fourth inch (2 1/4") inside hole diameter by one and one fourth inch (1 1/4") height.
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Available in 5ft and 6ft lengths.
Hose, cowl vent gutter drain.Length: 7.0 inches.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair and 6ft piece.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Grommet, firewall, for coil wire thermo tube, etc.
Boot, runningboard antenna wire connection.
Grommet, firewall wire harness, oil pressure tube, windshield wiper tube, capillary tube, radio antenna wire.
Grommet, firewall, for cowl vent drain hose and throttle control cable.