Covers, runningboard. Pre-molded.
Deflector, rear bumper stone. Exactly as original.
This windshield gasket set contains two (2) seals that mount around the perimeter's of both pieces of glass. It also has properly molded corners for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are molded in the shape of the window and designed from original parts for superior fitment and seal.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are molded as a straight piece and designed from original parts for superior fitment and seal.
Pad kit, body to frame. Thirty-four (34) piece set. Includes installation instructions.
Webbing, body to frame. Two (2) inch wide, twenty five (25) foot long roll.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Channel, flexible door window run. Stainless steel beaded. Available in 5ft lengths.
Grommets, front bumper arm. Fully molded rubber. Three and three fourths inch (3-3/4") outside length by two and five eighths inch (2-5/8") outside width. One and three fourths inch (1-3/4") inside hole lengths by one fourth inch (1/4") inside hole widths
Seal, lower door. Mounts to door scuff plates. Enough for 4 doors.
Seals, front of door.
This front door weatherstrip pair is designed from the original parts for superior fitment and seal. These door seals mount directly to the body to seal against the full perimeter of both the front left and front right doors.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair and 6ft piece.
Seals, lower door. Comes as a three (3) piece set but is enough to do all four (4) doors. The seal for the rear doors will need to be cut in half.
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair, 60", and 8ft lengths.
Fender welting. Thirty (30) foot roll. Black, textured finish. 1/4" bead.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 2ft pair, 3ft pair, and 6ft piece.
Bumper kit, hood. Deluxe.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 2ft and 3ft pairs.
Gasket, cowl vent.
Pads, brake and clutch pedal. Molded on metal like original. Exact pyramid design.Ford Truck 1937-40 Pads, pedal.
Pedal, accelerator. Original type.
Pads, fuel tank to frame.
Fender welting. Eight (8) foot length.
Weatherstrips, top of door. One strip is enough for two doors. Cut to fit as needed for all four door upper door openings. Mounts on body from approximately directly above the hinge to near the beltline of the car for the front door opening, and from beltline to beltline for the rear door opening.
Hose, fuel tank to filler neck connecting.
Bumper stops for the glovebox door - lower. Rubber Coated Steel like original. This part prevents the glovebox door from opening too far, reduces paint-chipping.
Bushings, stabilizer bar. Front.
Insulator, transmission gear shift column lever.
Axle Rebound Pad - Suspension bumper for front axle.
Axle Rebound Pad - Suspension bumper for rear axle.
Kit, hood to cowl weatherstrip. Forty-nine inch (49") extruded rubber strip includes installation screws.
Seals, brake and clutch pedal arms to floor board.
Pads, outside door handle.
Grommets, dash. Black.Ford Truck 1940 Grommets, dash. Black. Ford Cars 1938-40 Grommets, choke and throttle dash. Replacement rubber type.
Seal, transmission cover to floor.
Kit, door check arm and bumper. Enough for one door.
Seals, tie rod end. Four (4) piece set.
Grommets, emergency brake cable to radius rod bracket.
Grommet, cowl wiring firewall.
Grommet, emergency brake and speedometer cable through firewall.
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3 5/8") outside diameter by two and nine sixteenths inch (2 9/16") inside hole diameter by three and three sixteenths (3 3/16") sheet metal hole/retainin
Pads, upper hood hinge.
Grommets, horn bell to bracket.
Front or rear upper motor mount. Useage: Front motor mount for 1932-1947 Ford Trucks with 6 and 8 cylinders. Front motor mount for 1948-1951 Ford Trucks F-1, F-2, F-3. Two (2) required for trucks. Also used for 1932-1948: Ford & Mercury cars as a front
Pads, wiper stand. Replaces factory #78-17556.
Bumpers, front inner splash apron to frame. Four (4) piece set.Ford Truck 1948-52 Bumpers, gas tank to floor.
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.