Search Results
Windshield Gasket Set
p/n: 20-2202-50
This windshield gasket set contains two (2) seals that mount around the perimeter's of both pieces of glass. It also has properly molded corners for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 20-2346-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are molded in the shape of the window and designed from original parts for superior fitment and seal.
Front Door Vent Window Weatherstrips
p/n: 20-2345-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are molded as a straight piece and designed from original parts for superior fitment and seal.
Body Mounting Pad Kit
p/n: 20-2198-48
Pad kit, body to frame. Thirty-four (34) piece set. Includes installation instructions.
Body to frame webbing
p/n: 20-1599-48
Webbing, body to frame. Two (2) inch wide, twenty five (25) foot long roll.
Fenderskirt edge seal
p/n: 20-0111-44
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Flexible Run Channel
p/n: 20-1146-58
Channel, flexible door window run. Stainless steel beaded. Available in 5ft lengths.
Door Bottom weatherstrip
p/n: 70-3140-73
Seal, lower door. Mounts to door scuff plates. Enough for 4 doors.
Door Weatherstrip
p/n: 20-2253-73
This front door weatherstrip pair is designed from the original parts for superior fitment and seal. These door seals mount directly to the body to seal against the full perimeter of both the front left and front right doors.
Beltline Weatherstrip
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair and 6ft piece.
Door weatherstrip
p/n: 20-2368-73
Seals, lower door. Comes as a three (3) piece set but is enough to do all four (4) doors. The seal for the rear doors will need to be cut in half.
Flexible Run Channel
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair, 60", and 8ft lengths.
Fender Welting
p/n: 20-1590-44
Fender welting. Thirty (30) foot roll. Black, textured finish. 1/4" bead.
Motor mount kit
p/n: 20-1978-11
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Beltline Weatherstrip
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 2ft pair, 3ft pair, and 6ft piece.
Beltline Weatherstrip
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 2ft and 3ft pairs.
Brake and clutch pedal pad
p/n: 20-2307-22
Pads, brake and clutch pedal. Molded on metal like original. Exact pyramid design.Ford Truck 1937-40 Pads, pedal.
Door weatherstrip
p/n: 20-1646-73
Weatherstrips, top of door. One strip is enough for two doors. Cut to fit as needed for all four door upper door openings. Mounts on body from approximately directly above the hinge to near the beltline of the car for the front door opening, and from beltline to beltline for the rear door opening.
Glovebox Door Bumper Stops
p/n: 20-1698-88
Bumper stops for the glovebox door - lower. Rubber Coated Steel like original. This part prevents the glovebox door from opening too far, reduces paint-chipping.
Hood to Cowl Weatherstrip
p/n: 20-2184-42
Kit, hood to cowl weatherstrip. Forty-nine inch (49") extruded rubber strip includes installation screws.
Firewall grommet
p/n: 20-2279-88
Grommets, dash. Black.Ford Truck 1940 Grommets, dash. Black. Ford Cars 1938-40 Grommets, choke and throttle dash. Replacement rubber type.
Fuel neck grommet
p/n: 20-2177-39
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3 5/8") outside diameter by two and nine sixteenths inch (2 9/16") inside hole diameter by three and three sixteenths (3 3/16") sheet metal hole/retainin
Motor Mount
p/n: 20-1538-11
Front or rear upper motor mount. Useage: Front motor mount for 1932-1947 Ford Trucks with 6 and 8 cylinders. Front motor mount for 1948-1951 Ford Trucks F-1, F-2, F-3. Two (2) required for trucks. Also used for 1932-1948: Ford & Mercury cars as a front
Inner fender bumper
p/n: 20-0402-41
Bumpers, front inner splash apron to frame. Four (4) piece set.Ford Truck 1948-52 Bumpers, gas tank to floor.
Motor mount
p/n: 20-1539-11
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.
Headlight to fender gasket
p/n: 20-2295-14
Gasket, headlight bucket to fender. Cork. Two (2) required per vehicle.