This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Webbing, body to frame. Two (2) inch wide, twenty five (25) foot long roll.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Pad, deck handle base to trunk.
Grommets, front bumper arm. Fully molded rubber. Three and three fourths inch (3-3/4") outside length by two and five eighths inch (2-5/8") outside width. One and three fourths inch (1-3/4") inside hole lengths by one fourth inch (1/4") inside hole widths
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Bumpers, convertible header bow. Four (4) piece set.
Bumper kit, hood. Deluxe.
Gasket, cowl vent.
Pads, brake and clutch pedal. Molded on metal like original. Exact pyramid design.Ford Truck 1937-40 Pads, pedal.
Pedal, accelerator. Original type.
Pads, fuel tank to frame.
Kit, cowl lacing. Includes mounting screws.
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Hose, fuel tank to filler neck connecting.
Bumper stops for the glovebox door - lower. Rubber Coated Steel like original. This part prevents the glovebox door from opening too far, reduces paint-chipping.
Bushings, stabilizer bar. Front.
Insulator, transmission gear shift column lever.
Axle Rebound Pad - Suspension bumper for front axle.
Axle Rebound Pad - Suspension bumper for rear axle.
Kit, convertible striker bumper. Consists of four (4) bumpers for striker plates and four (4) bumpers for above and below striker.
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Seals, brake and clutch pedal arms to floor board.
Grommets, dash. Black.Ford Truck 1940 Grommets, dash. Black. Ford Cars 1938-40 Grommets, choke and throttle dash. Replacement rubber type.
Seal, transmission cover to floor.
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Seal, lower door. Two (2) required per car.
Grommets, emergency brake cable to radius rod bracket.
Grommet, cowl wiring firewall.
Grommet, emergency brake and speedometer cable through firewall.
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3 5/8") outside diameter by two and nine sixteenths inch (2 9/16") inside hole diameter by three and three sixteenths (3 3/16") sheet metal hole/retainin
Pads, upper hood hinge.
Grommets, horn bell to bracket.
This Front or Rear Upper Motor Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Pad, trunk handle base to trunk.
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.
Gasket, headlight bucket to fender. Cork. Two (2) required per vehicle.
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Grommet, emergency brake cable to frame.
Gaskets, parking light lens. Cork.
Pad, rear license plate bracket. Cork.
Grommet, wiper hose firewall.
Pad, battery hold down bracket.
Bumper, door jam.Qty Required:2 Two (2) required per car.
Pads, radiator to frame.
Seal, trunk handle license plate light lens.