Windshield Gasket
p/n: 20-2201-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Front bumper grommet
p/n: 20-2167-28
Grommets, front bumper arm. Fully molded rubber. Three and three fourths inch (3-3/4") outside length by two and five eighths inch (2-5/8") outside width. One and three fourths inch (1-3/4") inside hole lengths by one fourth inch (1/4") inside hole widths
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Door weatherstrip
p/n: 20-2368-73
Seals, lower door. Comes as a three (3) piece set but is enough to do all four (4) doors. The seal for the rear doors will need to be cut in half.
Trunk Handle Base Mounting Pad
p/n: 20-2385-86
This Trunk Handle Base Mounting Pad is designed from the original part for superior fitment, appearance and function. This correctly shaped with beaded edge mounting pad fits between the trunk handle base and the trunk compartment door.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Engine Mount
p/n: 20-1978-11
This Engine Mount set is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Brake and Clutch Pedal Pads
p/n: 20-2307-22
Brake and Clutch Pedal Pad pair. Molded on metal like original. Exact pyramid design. 1937-1940 Ford Trucks.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-2183-42
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part. This cowl lacing mounts with screws at the rear of the engine bay firewall directly to the body to seal between the hood and vehicle body cowl.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Glovebox Door Bumper Stops
p/n: 20-1698-88
Bumper stops for the glovebox door - lower. Rubber Coated Steel like original. This part prevents the glovebox door from opening too far, reduces paint-chipping.
Door Bumper Set
p/n: 20-2365-71
Set, convertible striker bumper. Consists of four (4) bumpers for striker plates and four (4) bumpers for above and below striker.
Hood Bumper Set
p/n: 20-2182-42
This fourteen (14) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Channel filler weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Door Check Link Rod End Stop
p/n: 20-1640-70
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Emergency Brake Cable Grommet
p/n: 20-2299-20
This Emergency Brake Cable Grommet is used for running the emergency brake cable and the speedometer cable through the firewall. Made from high-quality dense rubber to provide excellent durability.
Fuel Neck Grommet
p/n: 20-2177-39
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3-5/8") outside diameter by two and nine sixteenths inch (2-9/16") inside hole diameter.
Upper Engine Mount
p/n: 20-1538-11
This Front or Rear Upper Engine Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Choke and Throttle Rod Grommet
p/n: 20-2279-88
This Choke and Throttle Rod Grommet is used where the choke and throttle pass through the dash. Designed from the original part for superior fit and seal.
Lower Engine Mount
p/n: 20-1539-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Headlight to fender gasket
p/n: 20-2295-14
Gasket, headlight bucket to fender. Cork. Two (2) required per vehicle.
Convertible Roof Rail Weatherstrip
p/n: 20-1636-65
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Emergency Brake Cable Grommet
p/n: 20-2310-24
This Emergency Brake Cable Grommet is used when running the brake cable to the frame. Made from high-quality dense rubber to provide excellent durability.
Windshield Wiper Hose Grommet
p/n: 20-2300-20
This Windshield Wiper Hose Grommet is used to run the wiper hose through the firewall. Designed from the original part for superior fit and seal.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
