Gravel shield, rear fender. Molded in-car position with metal backing and holding tabs.Length: 15.75 inches.
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
This six (6) piece kit includes the inner and outer windowfelts and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models without vent windows in the door.
Motor mount, front. Two (2) per car. Revulcanization service only.
Gravel shield between body and rear fender, right and left, steel core.
Weatherstrip, rear door vent. For Buick order our #70-0695-74 division post weatherstrip separately. For Cadillac order our #70-0695-74 division post seal separately. For Chevrolet, we do not have a matching metal core division post seal for this part, yo
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Weatherstrip, hood to cowl.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Mounting pad, transmission (also called insulator or support pad). Revulcanization service only.Length: 5.0 inches. Width: 3.4375 inches.
Motor mount, rear. Revulcanization service only. One (1) per car.Width: 10.6875 inches.
Door weatherstrip. This set is the primary seal for the door to the body. Set contains two (2) seals for either the front or rear doors. Purchase two (2) sets if you need to complete all four (4) doors.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Pad, parking light (fender light).Width: 19.125 inches.
Mounting pad, taillight, right and left.Width: 10.5625 inches.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Pedal, accelerator. Black rubber. Revulcanization service only. For brown see our #70-1660-89.Length: 9.0 inches.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Pedal, accelerator. Brown rubber. Revulcanization service only. For black see our #70-1660-40.Color:brown Length: 9.0 inches.
Seal, fenderskirt edge. Each five (5) foot long. Similar to our #20-0111-44, but thicker.Length: 60.0 inches. Width: .25 inches.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Bumper, hood side pilot. Four (4) piece set required per car. Steel washer vulcanized inside rubber.
Mounting pad, trunk ornament, excellent material and workmanship.Width: 11.8125 inches.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Grommets, front bumper. Fully molded rubber. Five and three fourths inch (5-3/4") outside length by two and thirteen sixteenths inch (2-13/16") outside width by one and eleven sixteenths inch (1-11/16") inside hole length by nine sixteenths inch (9/16") i
Grommets, rear door vent divider post (wind deflector), upper and lower, right and left. Four (4) piece set.
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Bushings, front stabilizer bar mounting. Fits original bracket. Fully molded rubber. One and five eighths inch (1 5/8") length by one and three eighths inch (1 3/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter.
Bushings, rear stabilizer bar mounting. Fully molded rubber. One and one half inch (1 1/2") length by one and one fourth inch (1 1/4" outside diameter by nine sixteenths inch (9/16") inside hole diameter.
This Clutch Equalizer Bushing and Seal set is designed from the original part for superior fitment and operation. The set includes a metal sleeved rubber bushing and two (2) molded rubber seals for each end of equalizer shaft.
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Pinchweld seal, windshield, to seal and retain outer reveal molding. Used with our #70-1192-52. Twelve (12) foot strip.
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Rest pads, seat back, outer, on two (2) door styles with folding seats. Brown rubber. For black see our #70-0482-88. Self retaining, perfect copy.
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Pad, fender parking light lens.Width: 5.125 inches. Height: 2.25 inches.
Pad, hood side center rest.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Bumper, front suspension, upper arm.Height: 2.0 inches.
Division bar seal. Proper cross section rubber molded to original style metal with authentic attaching tabs. Note: used on front door vent assembly for selected 1937-38 convertible models and rear door vent on selected 1940-42 four door model
Rest pads, seat back, outer, on two (2) door styles with folding seats. Black rubber. For brown see our #70-0482-89. Self retaining, perfect copy.
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.