Stone shields, (gravel guards), rear fender.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Floor panels, pedal and steering column, tan rubber to match pedals. For hydramatic shift. Three (3) piece set. For manual shift see our #70-1218-89. We also have these avaliable in black. See parts #70-1218-88 (manual shift) and #70-1219-88 (hydramatic s
Floor panels, pedal and steering column, tan rubber to match pedals. For manual shift. Three (3) piece set. For hydramatic shift see our #70-1219-89. We also have these avaliable in black. See parts #70-1218-88 (manual shift) and #70-1219-88 (hydramatic s
Front motor mount. Revulcanizing core exchange only. Send your cores when ordering.
Floor panels, pedal and steering column, black rubber. For hydramatic shift. Three (3) piece set. For manual shift see our #70-1218-88. We also have these avaliable in tan. See parts #70-1218-89 (manual shift) and #70-1219-89 (hydramatic shift).
Floor panels, pedal and steering column, black rubber. For manual shift. Three (3) piece set. For hydramatic shift see our #70-1219-88. We also have these avaliable in tan. See parts #70-1218-89 (manual shift) and #70-1219-89 (hydramatic shift).
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Weatherstrip, hood to cowl. To facilitate manufacturing, some may be made in two sections.
Door edge weatherstrip. This part is the primary door to body weatherstrip and the upper hinge pillar weatherstrip. Adhesive not included in kit.
Pads, taillight mounting. Compound curved right and left hand custom molded pads. Also order the special design weatherproof gaskets for the lenses our #70-1213-15.
Filler, front fender dust shield, inner fender to frame including over upper control arm and around battery. Die cut from cotton reinforced sheet rubber.
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Gasket set for auxiliary light (fog light) body mounting.
Binding strip, dash insulator, lower edge, lower trim molding on firewall liner. Forty eight (48) inches long. Width: 2.25 inches.
Bumpers, front spring. Lower arm, original copy, integral molded plate and stud, three eighths (3/8) inch standard thread, for installing.
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
Pad set, license light mount and lens gasket.Length: 12.625 inches.
Gasket set, parking light and front turn signal. Four (4) piece set.
Fillers, side roof rail to front roof rail at front corner, right and left. Metal core, threaded for original screws.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top. Available in 29" pairs.
Filler, front door hinge pillar at dash, right and left. With metal core. Located at top front of front door, under door flange.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Bumper, front spring, upper arm (on frame).
Pad, accelerator pedal. Brown rubber. For black see our #70-0208-40. Made to slip over old metal core after removing old rubber.
Seal, fenderskirt edge. Each five (5) foot long. Similar to our #20-0111-44, but thicker.Length: 60.0 inches. Width: .25 inches.
Bottoming pads, rear axle. Rubber block mounts by bracket to rear axle tube.
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Gaskets, auxiliary light (fog light) opening cover to fender.
Bumper, door side. Square type held by four (4) screws, metal core as original.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Pads, brake and clutch pedals. Brown rubber. For black see our #70-0176-22.Color:brown Length: 3.8125 inches.
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Seal, rear gravel deflector to bumper face bar (staples to gravel deflector), three thirty seconds (3/32) inches by one and three fourths (1-3/4) inch
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber.Length: 8.25 inches.
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Pinchweld seal, windshield, to seal and retain outer reveal molding. Used with our #70-1192-52. Twelve (12) foot strip.
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Cushion, trunk lock striker.
Rest pads, seat back, outer, on two (2) door styles with folding seats. Brown rubber. For black see our #70-0482-88. Self retaining, perfect copy.
Spacer or mute, front and rear bumper mounting bar to gravel deflector. Fully molded rubber. Two and nine sixteenths inch (2-9/16") outside length by seven eighths inch (7/8") width by thirteen sixteenths inch (13/16") height.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Gasket, taillight lens. For the main pad order our #70-1212-15.Length: 6.875 inches.
Gasket, firewall opening for fresh air intake.
Bumpers, hood top panel at cowl. One half (1/2) inch by one half (1/2) inch by three and one fourth (3-1/4) inch. Held in place by screws. Two (2) to four (4) per car as required.