Please click on the part name in red in order to get a complete description.
Runningboard covers. Imported.
Seal, rear bumper stone deflector.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. The main seals are molded in the shape of the window and designed from original parts for superior fitment and seal.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are molded in the shape of the window and designed from original parts for superior fitment and seal.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. The main seals are molded as a straight piece and designed from original parts for superior fitment and seal.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are molded as a straight piece and designed from original parts for superior fitment and seal.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Pad kit, body to frame. Nineteen (19) piece set. Installation instructions included.
Webbing, body to frame. Two (2) inch wide, twenty five (25) foot long roll.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Channel, door glass flexible run. Fabric covered bead. Sixty (60) inches long. Measures 9/16” tall x 5/8” wide. Used with 1/4” glass.
Channel, flexible door window run. Stainless steel beaded. Sixty (60) inches long.
Weatherstrips, closed car door hinge. Molded to fit hinge area.
Grommets, front bumper arm.
Grommets, rear bumper arm.
Window felt inner and/or outer. One (1) pair of three (3) foot lengths. Flexible, pile lined, rubber covered, with black bead. For front door, rear door and quarter windows.
Seals, floor board.
Fender welting. Thirty (30) foot roll. Black, textured finish. 1/4" bead.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Pads, brake and clutch pedal. Concentric circle design.
Gasket, cowl vent.
Pedal, accelerator. Original type.
Bumper kit, hood.
Fender welting. Eight (8) foot length.
Weatherstrips, top of door. Mounts on body from approximately just above the hinge to near the beltline on the lock side of the car. Each door opening strip is made from top quality closed cell sponge rubber approximately 54 inches long.
Pads, parking light.
Weatherstrips, lower back of door.
Bumper stops for the glovebox door - lower. Rubber Coated Steel like original. This part prevents the glovebox door from opening too far, reduces paint-chipping.
Bushings, stabilizer bar. Front.
Insulator, transmission gear shift column lever.
Seal, steering column tube. Installs on top of floor mat.
This rubber Cowl Lacing is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body to seal between the firewall and hood.
Seal, steering column tube. Installs under floor mat.
Hose, fuel tank to filler neck.
Seals, brake and clutch pedal arms to floor board.
Weatherstrips, closed car back of door. Vertical section on lock side of door.
Gaskets, taillight housing to body.
Bumper, front or rear axle.Truck: Typically order two per truck.
Kit, door check arm and bumper. Enough for one door.
Weatherstrips, lower door.
Seals, tie rod end. Four (4) piece set.
Grommet, emergency brake and speedometer cable firewall.
Grommet, cowl wiring firewall.
Pads, upper hood hinge.
Grommets, horn bell to bracket.
Front or rear upper motor mount. Useage: Front motor mount for 1932-1947 Ford Trucks with 6 and 8 cylinders. Front motor mount for 1948-1951 Ford Trucks F-1, F-2, F-3. Two (2) required for trucks. Also used for 1932-1948: Ford & Mercury cars as a front
Pad, deck handle base.
Bumpers, gas tank door.
Front vent window division post seal. Extruded rubber strip only that will have to be attached to division post.
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.
Gasket, headlight bucket to fender. Cork.
Pads, striker plate.
Bumpers, upper door. Closed cars.
Gaskets, taillight lens. Cork.Ford Truck 1948-56 Gaskets, lens to housing. Ford Cars 1941 Gaskets, taillight lens.
Gaskets, parking light lens.
Seal, wiper pivot shaft to roof or cowl. Small type. Replaces factory #11A-17541. Note: this part is used as a wiper pivot shaft to roof in 1937-1939. It is used as a wiper pivot shaft to cowl in 1941-1948.
Seal, wiper pivot shaft to cowl. Large type. Replaces factory #7C-17541.
Pad, rear license plate bracket. Cork.
Seals, deck handle base license plate lens. 3 piece set.
Grommet, wiper hose through firewall.
Grommet, headlight bucket wiring.
Bumper, door jam.Qty Required:2 Two (2) required per car.
Pads, radiator to frame.
Grommet, choke and throttle rod or hood pull cable firewall.1932-47: All Trucks for choke & throttle rod; 1957-63: All Trucks for choke & wiper.
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Bumper, door check arm.