Please click on the part name in red in order to get a complete description.
Runningboard covers. Imported.
Seal, rear bumper stone deflector.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. The main seals are molded in the shape of the window and designed from original parts for superior fitment and seal.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are molded in the shape of the window and designed from original parts for superior fitment and seal.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. The main seals are molded as a straight piece and designed from original parts for superior fitment and seal.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are molded as a straight piece and designed from original parts for superior fitment and seal.
Pad kit, body to frame. Nineteen (19) piece set. Installation instructions included.
Webbing, body to frame. Two (2) inch wide, twenty five (25) foot long roll.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Channel, door glass flexible run. Fabric covered bead. Sixty (60) inches long. Measures 9/16” tall x 5/8” wide. Used with 1/4” glass.
Channel, flexible door window run. Stainless steel beaded. Sixty (60) inches long.
Weatherstrips, closed car door hinge. Molded to fit hinge area.
Grommets, front bumper arm.
Grommets, rear bumper arm.
Window felt inner and/or outer. One (1) pair of three (3) foot lengths. Flexible, pile lined, rubber covered, with black bead. For front door, rear door and quarter windows.
Weatherstrip, back of door, vertical section. Material enough for all four doors, cut to fit at installation.
Seals, floor board.
Weatherstrips, lower door. Set of three (3) pieces. Use full length for front doors, cut third piece in half to complete installation for both rear doors.
Fender welting. Thirty (30) foot roll. Black, textured finish. 1/4" bead.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Pads, brake and clutch pedal. Concentric circle design.
Gasket, cowl vent.
Pedal, accelerator. Original type.
Bumper kit, hood.
Fender welting. Eight (8) foot length.
Weatherstrips, top of door. One strip is enough for two doors. Cut to fit as needed for all four door upper door openings. Mounts on body from approximately directly above the hinge to near the beltline of the car for the front door opening, and from beltline to beltline for the rear door opening.
Pads, parking light.
Weatherstrips, lower back of door.
Bumper stops for the glovebox door - lower. Rubber Coated Steel like original. This part prevents the glovebox door from opening too far, reduces paint-chipping.
Bushings, stabilizer bar. Front.
Insulator, transmission gear shift column lever.
Seal, steering column tube. Installs on top of floor mat.
This rubber Cowl Lacing is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body to seal between the firewall and hood.
Seal, steering column tube. Installs under floor mat.
Hose, fuel tank to filler neck.
Seals, brake and clutch pedal arms to floor board.
Gaskets, taillight housing to body.
Bumper, front or rear axle.Truck: Typically order two per truck.
Kit, door check arm and bumper. Enough for one door.
Seals, tie rod end. Four (4) piece set.
Grommet, emergency brake and speedometer cable firewall.
Grommet, cowl wiring firewall.
Pads, upper hood hinge.
Grommets, horn bell to bracket.
Front or rear upper motor mount. Useage: Front motor mount for 1932-1947 Ford Trucks with 6 and 8 cylinders. Front motor mount for 1948-1951 Ford Trucks F-1, F-2, F-3. Two (2) required for trucks. Also used for 1932-1948: Ford & Mercury cars as a front
Bumpers, gas tank door.
Front vent window division post seal. Extruded rubber strip only that will have to be attached to division post.
Mount, front motor. Lower.Ford Truck 1932-47: All Ford Trucks, 2 each required. 1948-51: Ford F100 Series both 6 or 8 cylinder, 1 each required.
Gasket, headlight bucket to fender. Cork.
Pads, striker plate.
Bumpers, upper door. Closed cars.
Gaskets, taillight lens. Cork.Ford Truck 1948-56 Gaskets, lens to housing. Ford Cars 1941 Gaskets, taillight lens.
Gaskets, parking light lens.
Seal, wiper pivot shaft to roof or cowl. Small type. Replaces factory #11A-17541. Note: this part is used as a wiper pivot shaft to roof in 1937-1939. It is used as a wiper pivot shaft to cowl in 1941-1948.
Seal, wiper pivot shaft to cowl. Large type. Replaces factory #7C-17541.
Pad, rear license plate bracket. Cork.
Seals, deck handle base license plate lens. 3 piece set.
Grommet, wiper hose through firewall.
Grommet, headlight bucket wiring.
Bumper, door jam.Qty Required:2 Two (2) required per car.
Pads, radiator to frame.
Grommet, choke and throttle rod or hood pull cable firewall.1932-47: All Trucks for choke & throttle rod; 1957-63: All Trucks for choke & wiper.
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Bumper, door check arm.