Please click on the part name in red in order to get a complete description.
Gasket, trunk stop lamp lens. Used on the decklid center of the trunk. Fully molded rubber.
Lacing, hood cowl. Forty nine (49) inches long. Cloth anti-squeak material where hood rests on cowl. Includes tacks.
Grommet, fuel filler neck.
Front coil spring pad
Cushion ring, horn button contact, upper.
Boot, steering column vacuum cylinder. Excellent duplicate of original. Made of durable, long lasting rubber.Length: 5.50 inches.
Nipple, coil wire to distributor at coil end.
Gasket, cowl vent. These parts are made of the highest quality and authenticity.Length: 15.0 inches.
Pad, convertible top assembly. Rubber only, cements to original metal core.
Pad, rear license light body.Length: 7.0 inches. Width: 3.375 inches.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Gasket, taillight housing. Also order #70-0471-15 for the taillight mounting pad, and for the taillight lens gasket order #70-0658-15.Length: 8.25 inches.
Anti-squeak, hood to cowl. Five eighths (5/8) inch by seven thirty seconds (7/32) inch. One eight (8) foot strip per vehicle.Length: 96.0 inches.
Pads, parking light.
Plugs, door bottom, self-retaining, oval.
Anti-squeak, hood ledge (cowl). One (1) pair required per car.Length: 25.5 inches. Width: .625 inches. Height: .21875 inches.
Weatherstrip, door lock, front and rear. Protects door lock mechanism from dust and weather.Length: 3.625 inches.
Grommet, firewall, main wiring harness plus up to five (5) accessory wires.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts on the lower length of the trunk directly to the body.
Channel, side window glass, vertical run. (Use our #40-0280-57 across top).
Seal, gearshift at floor. See our #60-0397-24 for 4 speed transmission.
Fender welting. Thirty (30) foot roll. Black, textured finish. 1/4" bead.
Bushing, rear axle track bar. Made in halves for easier replacement. Sold in pairs, two (2) pair needed per bar.Height: .75 inches.
Retainer, for outside windshield center post stainless molding. Use with original stainless molding and clips.Length: 15.5 inches. Width: 1.25 inches.
Seals, back of front fender to cowl.
Grommets, top motor to firewall bracket. Three (3) piece set.
Grommets, front bumper arms to splash pan rubber. Four (4) piece set.
Seal, rear bumper to stone deflector rubber.
Kit, motor mount. Enough for one motor mount. Kit includes one (1) each of 78-6029-A, B-6038-C, 78-6048-A, B-6039-A, and B-6047.
Grommets, runningboard to frame and front fender to cowl. Rubber grommets and metal washers. Twenty four (24) piece set.
Shackle set, spring. Front. Original steel stud type.
Seal gearshift at floorboard. Sponge rubber, one half (1/2) inch thick. One required per vehicle.Length: 6.5 inches. Width: 6.5 inches. Height: .50 inches.
Bumper, rear bumper deflector. Two (2) per car.Chevrolet 1942-55 Bumper, rubber, radiator grille, lower panel.Length: 2.1875 inches.
Pad, rear license light and trunk handle body.Length: 7.50 inches.
Tape, black bowdrill cloth. Adhesive backed, used to create cloth cover surface for side rail weatherstrips typically. Five (5) inches by five (5) foot roll. Pressure sensitive, for covering convertible side window weatherstrip such as our #70-1170-99 or
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Boot, gearshift on steering column. Brown rubber. For black see our #30-0069-36. Two and one eighth (2-1/8) inch long style.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Gasket, parking light lens. Top quality one eighth (1/8) inch sponge.Length: 5.50 inches. Width: 1.75 inches.
Mounting pad, trunk handle escutcheon.Length: 6.75 inches.
Filler valance or deflector, rear. Eight (8) inches long (cut shorter where required), three (3) to four (4) required per car.
Grommet, fuel filler neck with proper retaining flange. Oval style. Three and three fourths inch (3-3/4) outside width by four and one half inch (4-1/2") outside length by three fourths (3/4") inch height. Two and one sixteenth inch (2 1/16") top hole wi
Boot, parking light socket.
Seal, accelerator rod through floorboard.
Anti-squeak, hood to cowl, two (2) piece set for right and left.Length: 38.0 inches. Width: .625 inches. Height: .21875 inches.
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Pads, brake and clutch pedal. Concentric circle design.
Bushings, stabilizer bar. Front.
Weather deflector, edge of folding top fabric near folding post, mounted on body.Length: 1.75 inches. Width: .625 inches.
Grommets, license light wire. Two (2) per car.
Grommet, speedometer cable through firewall. Retained by steel collar (not included). Two and one half (2-1/2) inch outside diameter.
Filler, rear bumper gravel deflector. Die cut masticated sheet rubber. Approximately eleven (11) inches overall long.
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Pad, brake and clutch pedal. Black rubber. For brown see our part #50-0054-89. Perfect copy, fine detail.Width: 3.125 inches. Height: 2.125 inches.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Includes enough to do front, top and backside of one door.
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Gasket, cowl vent.
Pad, deck handle base.
Seal, lower suspension arm, inner. Four (4) piece set.
Boot, brake master cylinder rod. Fits on one and one fourth (1-1/4) inch diameter cylinder. Height: 2.125 inches.
Insulators, front coil spring. Fabric reinforced rubber as original.
Bumper, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with our #60-0579-24.
Boot, gearshift on steering column. Black rubber. For brown see our #30-0069-89. Two and one eighth (2-1/8) inch long style.Length: 2.25 inches.
Boot, starter solenoid.
Grommet, firewall, vacuum operated radio antenna lines.
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Boot, gear shift. Taupe.
Pedal, accelerator. Original type.
Bumper kit, hood.
Channel, quarter window glass to stainless frame rubber.
Gasket, outside door handle. Precision die cut from one thirty seconds (1/32) inch dense rubber to fit original factory handles.
Insulator, exhaust system, muffler pipe bracket. Also intermediate pipe bracket on extra-long body styles. Two (2) required per car, most models.
Grommet, wire harness-thru-firewall mat. Two (2) inch diameter with two and one fourth (2-1/4) inch outside diameter flange.
Gasket, divided windshield center post. Combines inner and outer gasket in one piece as original. Seventeen (17) inch to (20) inch lengths.Length: 20.
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Seal, steering column tube. Installs under floor mat.
Seal, steering column at toe board, for steering column housing and shifter control shaft jacket. Top quality sponge rubber, accurately cut.
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Fender welting. Eight (8) foot length.
Boot, battery cable at starter solenoid.Width: 2.75 inches.
Bumper kit, hood.
A pair of retainers for lower door seal.
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Weatherstrips, top of door. One strip is enough for two doors. Cut to fit as needed for all four door upper door openings. Mounts on body from approximately directly above the hinge to near the beltline of the car for the front door opening, and from beltline to beltline for the rear door opening.
This Leading Edge Vertical Weatherstrip seal pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Weatherstrips, top of door. Mounts on body from approximately just above the hinge to near the beltline on the lock side of the car. Each door opening strip is made from top quality closed cell sponge rubber approximately 54 inches long.
Boot, electrical connection, generator terminal or ignition coil at engine.
Grommet, firewall, oblong four (4) hole style. Fits steel retainer for throttle and choke cables, oil and temperature lines.
Boot, battery cable at starter solenoid.
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Mounting pad, vacuum operated fender mounted antenna with one and one half (1-1/2) inch base.
Weatherstrips, lower back of door.
Headlight housing to fender gasket. Steel rule die-cut replacement for #1320452.
Roller, hood rear center rest.
Lacing, hood cowl.
Pad, body mounting. Fully molded rubber with metal core & locating collar. One and seven eighths inch (1 7/8") outside diameter by one and one eighths inch (1 1/8") locating collar outside diameter by three fourths inch (3/4") locating collar inside diame
Vent window division post seal. Single approximate 32 inch strip of original cross section extruded rubber that must be cut in half to complete a pair for both the driver and passenger side door vents. To install this part, one typically uses an ad