This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it. It has properly molded corners to precisely conform to the glass and molded sections for the wiper transmissions. It also has the slot to accommodate the locking strip.
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Weatherstrip, hood to cowl. 56 1/2 " long. Note: compare to #50-0436-43 hood to cowl sold separately.
Motor mount, front. Revulcanization service only.Qty Required:2 Length: 3.375 inches. Width: 2.625 inches. Height: 1.25 inches.
Support pad, transmission mount (insulator). Revulcanization service only.Length: 5.0 inches. Width: 2.0 inches.
Support, transmission (insulator). Revulcanization service only. See also our #50-0262-25, many models use both.Length: 5.0 inches. Width: 1.875 inches.
Pad, transmission mounting, thrust. Revulcanization service only. One (1) per car required. See also our #50-0263-25. Many models use both.Length: 7.
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.
Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top. Available in 29" pairs.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Seal, fenderskirt edge. Good quality and workmanship, see sketch for comparison. Ten (10) foot strip.Length: 120.0 inches. Width: .1875 inches.
Boot, torque ball.
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Pad, accelerator pedal. Brown rubber. For black see our #50-0160-40. Slip-over type for old core, perfect copy.Color:brown Length: 9.0 inches.
Seal plate, hood fastener control, cable through firewall. Rubber with brass core.
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Pad, accelerator pedal. Black rubber. For brown see our #50-0160-89. Slip-over type for old core, perfect copy.Length: 9.0 inches.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Bumper, front suspension, upper arm.Height: 2.0 inches.
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber. One and one half inch (1 1/2") length by one and one half inch (1 1/2") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half in
Pad, brake and clutch pedal. Brown rubber. For black see our part #50-0054-22. Perfect copy, fine detail.Color:brown Width: 3.125 inches.
Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Available in 5ft and 6ft lengths.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair and 6ft piece.
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, twenty five (25) foot roll. Typially used for attaching two (2) fenders to body. For f
Bumpers, front door, upper. Approximately five eighths (5/8) inch square, three eighths (3/8) inch inside diameter. Steel core, retained by screw.
Headlight body mounting gasket. Rubber.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.
Retainer, for outside windshield center post stainless molding. Use with original stainless molding and clips.Length: 15.5 inches. Width: 1.25 inches.
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Pad, brake and clutch pedal. Black rubber. For brown see our part #50-0054-89. Perfect copy, fine detail.Width: 3.125 inches. Height: 2.125 inches.
Insulators, front coil spring. Fabric reinforced rubber as original.
Gasket, taillight lens. Die cut from three sixteenths (3/16) inch sponge.Width: 8.75 inches. Height: 3.875 inches.
Boot, starter solenoid.
Boot, battery cable at starter solenoid.Width: 2.75 inches.
Grommet, glovebox door check link, for one (1) inch slot in dash.
Pad, body mounting. Fully molded rubber with metal core & locating collar. One and seven eighths inch (1 7/8") outside diameter by one and one eighths inch (1 1/8") locating collar outside diameter by three fourths inch (3/4") locating collar inside diame
Pad, mounting, hydraulic pump. Used on models with hydraulic window lifts or hydraulic convertible top. Two (2) to three (3) required. per car.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Grommet, speedometer cable & windshield washer lines through firewall.Width: 2.3125 inches. Height: 1.9375 inches.