Hardtop roof rail weatherstrip (Main seal). This part fits on the roof of the vehicle and seals the side window when the window is fully raised. Note: order #70-0378-63 hinge pillar seal separately.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it. It has properly molded corners to precisely conform to the glass and molded sections for the wiper transmissions. It also has the slot to accommodate the locking strip.
This rear window gasket set contains the rear window gasket itself and the locking strip. The gasket has the divider bars molded directly into it and has molded corners for a precise, factory fit.
Dust seals, rear fender at bumper.
Duct, defroster, instrument panel to door. Brown rubber. For black see our #70-0446-31.
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front motor mount cushion. Revulcanization service only. Send in cores and allow three weeks for service. Include inner core
Scoop, air intake at front end sheet metal.
Duct, defroster, instrument panel to door. Black rubber. For brown see our #70-0446-89.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Weatherstrip, hood to cowl. High quality rubber molded in one piece as original.
Engine harmonic balancer. Revulcanization service only. Send in your old, rebuildable balancer and pulley assembly.
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed. Note: order #70-0379-68 hardtop roof rail seals separately.
This 1948 - 1959 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems. This information set is a high-quality reproduction of the exact parts manual originally published for use by Cadillac dealer mechanics.
Cushion, motor support, rear on transmission to cross member. Revulcanization service only.
Cushion support, motor, rear on transmission to cross member. Revulcanization service only. Similar to #70-0674-11.Length: 3.75 inches. Width: 2.25 inches.
This trunk weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Bumpers, front spring. Lower arm, original copy, integral molded plate and stud, three eighths (3/8) inch standard thread, for installing.
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top. Available in 29" pairs.
Gasket set, taillight assembly. Four (4) piece set for lens and housing, right and left.
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide, three sixteenths (3/16) inch, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty fi
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Bumper, front spring, upper arm (on frame).
Pad, accelerator pedal. Brown rubber. For black see our #70-0208-40. Made to slip over old metal core after removing old rubber.
Gasket, heater to firewall.
Bottoming pads, rear axle. Rubber block mounts by bracket to rear axle tube.
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Seal, fog light body. Without notches. For seal with notches see our #70-1242-17.Length: 6.5 inches. Width: 7.75 inches.
Seal, fenderskirt edge. Good quality and workmanship, see sketch for comparison. Ten (10) foot strip.Length: 120.0 inches. Width: .1875 inches.
Pad, backup light mounting. Made with angled surface to align light with body.
Bumper, door side. Square type held by four (4) screws, metal core as original.
Pads, brake and clutch pedals. Brown rubber. For black see our #70-0176-22.Color:brown Length: 3.8125 inches.
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Seal, rear gravel deflector to bumper face bar (staples to gravel deflector), three thirty seconds (3/32) inches by one and three fourths (1-3/4) inch
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber.Length: 8.25 inches.
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Bumper, front seat back center arm hinge. Excellent finish and details with original style metal core. See our #70-0482-88 for outer seat back bumper.
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Cushion, trunk lock striker.
Rest pads, seat back, outer, on two (2) door styles with folding seats. Brown rubber. For black see our #70-0482-88. Self retaining, perfect copy.
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
Grommet, main wiring harness and misc. wires through firewall (main cable and up to eight (8) other wires, tubes or cables).
Pads, brake and clutch pedals. Black rubber. For brown see our #70-0176-89.
Rest pads, seat back, outer, on two (2) door styles with folding seats. Black rubber. For brown see our #70-0482-89. Self retaining, perfect copy.
Grommet, steering column at floor, fits chrome ring.