Please click on the part name in red in order to get a complete description.
Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Eight (8) piece kit includes inner and outer felt beltline weatherstrip for each door and quarter windows. These strips wipe the side windows when the glass is
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Door edge weatherstrip. Includes front and rear door seals. This part is the primary door to body weatherstrip.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it. It has properly molded corners to precisely conform to the glass and has the slot to accommodate the outer edge's decorative molding.
This rear window gasket set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Seal, rear bumper stone deflector. Three (3) piece set.
Pad, brake pedal. Merc-O-Matic transmission.
Seals, brake and clutch arm.
Pad, fenderskirt edge, similar to our #70-0055-45, but thinner. Approximately five (5) foot strip per skirt.Length: 60.0 inches. Width: .15625 inches.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Pad, luggage compartment door handle.
Pads, brake and clutch pedal. Standard transmission.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Seal pad, rubber tape. Fifteen (15) foot roll.
Pads, windshield wiper pivot. Use when windshield washer is part of wiper pivot. Replaces factory #8M-17541-B.
Grommet, fuel filler neck.
Seal, steering column tube. Installs on top of floor mat.
Seals, taillight lens to housing.
Kit, cowl lacing. Includes special tacks.
Bumper kit, hood.
Seal, top outside corners of cowl to hood. Includes left and right side.
Bumper, rear lamp bracket. Type w/Tire Carrier.
Hose, fuel tank to filler neck.
Repair kit, gear shift lever grommet. Column shift only. Two (2) kits required.
Grommet, glove compartment door check arm.
Seals, brake and clutch pedal arms to floor board.
Pads, door handle. Outside. Four (4) piece set.
Seals, tie rod end. Four (4) piece set.
Gaskets, parking light lens to housing.
Grommet, overdrive pull cable.
Grommet, main wiring loom firewall.
Grommet, door lock button to garnish molding.
Pads, door lock cylinder assembly to door.
Seal, front suspension. Inner upper arm.Qty Required:4 Four (4) required per car.
Bumper, quarter panel fuel filler lid.
Grommet, wiper arm to motor. Replaces factory #51A-17562.
Seal, idler arm. Two (2) required per car.
Grommet, wiper hose. Replaces factory #8A-17545-S.
Grommet, speedometer cable firewall.
Grommet, air vent cable through firewall. One pair required per vehicle.
Seal, front suspension. Inner lower arm.Qty Required:4 Four (4) required per car.
Grommet, rear shock absorber.
Grommet, front shock absorber. Four (4) required per shock.
Bushing, shock absorber link. May be used for front or rear spring.Chrysler 1951-54 Bushing, rubber, shock absorber link.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Plug, cowl and floor pan. Three fourths (3/4) inch.
Bumper, door check arm.