Search Results
Please click on the part name in red in order to get a complete description.
Front + Rear Door weatherstrip
p/n: 20-3114-72
Door edge weatherstrip. Includes front and rear doors. This part is the primary door to body weatherstrip.
Front Door Vent Window Kit
p/n: 90-0323-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door weatherstrip
p/n: 20-3110-72
Front door edge weatherstrip. Cut as required. This part is the primary door to body weatherstrip.
Front Door Vent Window Weatherstrips
p/n: 20-3037-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Windshield Gasket
p/n: 20-3030-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 20-3131-81
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Flexible run channel
p/n: 20-1619-58
Channel, door glass flexible run. Fabric covered bead. Sixty (60) inches long. Measures 9/16” tall x 5/8” wide. Used with 1/4” glass.
Flexible run channel
p/n: 20-1146-58
Channel, flexible door window run. Stainless steel beaded. Sixty (60) inches long.
Beltline weatherstrip
p/n: 40-0539-57
Window felt inner and/or outer. One (1) pair of three (3) foot lengths. Flexible, pile lined, rubber covered, with black bead. For front door, rear door and quarter windows.
Beltline weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Peel-N-Stick Trunk Weatherstrip
p/n: 20-1389-WT
This trunk weatherstrip is a replacement part designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance. Excellent for use on many different vehicle models.
Side window weatherstrip
p/n: 30-0244-57
Window felt inner and/or outer. One (1) pair of three (3) foot lengths. Flexible, pile lined, rubber covered, with black bead. For front door, rear door and quarter windows.
Splash apron
p/n: 20-3014-44
Weatherstrips, front fender splash apron to frame. Installed on fender splash apron. Six (6) pieces per kit.
Vent division bar weatherstrip
p/n: 20-3040-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Trunk Weatherstrip
p/n: 20-1389-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Gravel shield anti-squeak
p/n: 20-2957-29
Seal, rear stone deflector. Installs between body & rear bumper.
Engine Mount
p/n: 20-2401-11
Front Engine Mount - Two (2) required per car. Ford only 6 or 8 cylinder engines.
Gravel shield anti-squeak
p/n: 20-3010-44
Seal, front fender anti-squeak. Installs at splash apron to rear of splash to body. One hundred forty (140) inches long.
Air ventilator seal
p/n: 20-2965-31
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Steering column floorplate
p/n: 20-3158-88
Seal, steering column to floor. Installs under floor mat.
Steering column floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Air ventilator seal
p/n: 20-2966-31
Gaskets, ventilator air valve.1952-54: 1 pair required. 1955-56: 2 pair required.
Front suspension bumper
p/n: 20-2475-32
Bumper, front suspension lower arm. Bumper section is 2" tall and 1-15/16" wide.
Spring shackle bushing kit
p/n: 20-2481-33
Bolt and bushing, front of rear spring. Two (2) kits required per car.
Stabilizer Bushing
p/n: 20-2985-33
Bushing, stabilizer bar. One and five sixteenths inch (1 5/16") length by one and one fourth inch (1 1/4") width by five eighths inch (5/8") inside hole diameter by one and seven sixteenths inch (1 7/16') height at ends. Four (4) required per vehicle.
Front bumper grommet
p/n: 20-2507-45
Grommets, front stone deflector to bumper arm anti-rattler. Four and one half (4-1/2) inch long. Two (2) piece set.
Front suspension bushing
p/n: 20-2474-32
Seal, front suspension lower control arm outer. Four (4) required per car.
Front suspension bushing
p/n: 20-2471-32
Seal, front suspension. Inner upper arm.Qty Required:4 Four (4) required per car.
Glovebox and fuel door bumper
p/n: 20-1220-88
Bumpers, glovebox and/or fuel filler door. Used as glove box door bumpers for all models listed, used as fuel door bumper for 1950-51 cars and 57-59 retractables only.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Front suspension bushing
p/n: 20-2470-32
Seal, front suspension. Inner lower arm.Qty Required:4 Four (4) required per car.
Front suspension bushing
p/n: 20-2473-32
Seal, front suspension outer upper arm. Four (4) required per car.
Shock absorber bushing
p/n: 20-1274-32
Bushing, shock absorber link. May be used for front or rear spring.Chrysler 1951-54 Bushing, rubber, shock absorber link.
Body Hole Plug
p/n: 20-1040-21
Plug, hole in dog leg cover. Installs at front of door where bolt to adjust vent window frame is located. This body plug covers a sheet metal hole that is one and one half (1-1/2) inch in diameter.
Body Hole Plug
p/n: 20-1039-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one fourth (1-1/4) inch in diameter.
Brake adjustment hole plug
p/n: 70-1092-24
Plug, brake adjustment hole. Fits five sixteenths (5/16) inch by one (1) inch slot. Most models with drum brakes.Length: 1.25 inches. Height: .875 inches.
