Front suspension bumper
p/n: 50-0092-32
Bumper, front suspension, lower arm. Steel core, with threaded stud, as original. Two (2) per car required.
Front Suspension Bumper
p/n: 27-0080-32
This Front Suspension Bumper, front suspension lower A-arm, is made from high-quality EPDM rubber for a precise, factory fit.
Front suspension bushing
p/n: 20-2473-32
Seal, front suspension outer upper arm. Four (4) required per car.
Front suspension bushing
p/n: 20-2471-32
Seal, front suspension. Inner upper arm.Qty Required:4 Four (4) required per car.
Front suspension bushing
p/n: 20-2470-32
Seal, front suspension. Inner lower arm.Qty Required:4 Four (4) required per car.
Front suspension bushing
p/n: 20-2474-32
Seal, front suspension lower control arm outer. Four (4) required per car.
Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Fuel Filler Neck Grommet
p/n: 60-0512-41
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fully molded rubber, slightly angled and oblong in shape.
Fuel Neck Grommet
p/n: 70-1616-39
Grommet, fuel neck. Fully molded rubber with retaining flange. Three and eleven sixteenths inch (3-11/16") outside diameter by two and one eighth inch (2-1/8") inside hole diameter by nine sixteenths inch (9/16") height.
Fuel Neck Grommet
p/n: 20-0581-39
Grommet, gas tank neck. Oval shaped. Fully molded rubber with retaining flange. Three and thirteen sixteenth inch (3-13/16") outside width by four and five sixteenths inch (4-5/16") outside length.
Fuel Neck Grommet
p/n: 60-0149-41
Grommet, fuel filler neck (1955-1st type). Oblong fully molded rubber with retaining flange. Three and seven eighths inch (3-7/8") outside width by five and one eight inch (5-1/8") outside length by one and one eighth inch (1-1/8") height.
Fuel Neck Grommet
p/n: 60-0271-41
Grommet, fuel filler neck. Oblong shaped molded rubber with retaining flange. Three and three fourths inch (3-3/4") outside length by three and five eighths inch (3-5/8") outside width.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Gearshift Knob
p/n: 20-0583-24
This black floor shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct screw on replacement for that broken, aged-out original knob.
Gearshift Knob
p/n: 20-0461-24
This black ball column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct push on replacement for that broken, aged-out original knob.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Glovebox or Fuel Tank Filler Door Bumpers
p/n: 20-1220-88
This Glovebox or Fuel Tank Filler Door Bumper pair is a quality reproduction of the original factory part. This push on rubber bumper attaches to support / cushion the glovebox or filler door closure.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
Gravel shield bumper
p/n: 70-2825-44
Anti-rattler, front stone shield. Insulates the front stone shield from the front bumper. Six (6) piece set.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Hardtop Roof Rail Weatherstrip
p/n: 40-0456-68
Hardtop roof rail weatherstrip. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Hardtop Roof Rail Weatherstrips
p/n: 20-3103-68
This Hardtop Roof Rail Weatherstrip pair fits on the roof of the vehicle and seals the side window when the window is fully raised.
Harmonic balancer service
p/n: 70-1047-12
Engine harmonic balancer. Revulcanization service only. Send in your old, rebuildable balancer and pulley assembly.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Headliner Retainer Clip
p/n: 20-0575-88
Clip, roof headliner and seal retainer. Sixteen (16) clips required.
Headliner Retainer Clip
p/n: 20-0576-88
Clips, roof headliner and seal retainer. Set of sixteen (16) pieces.
Headliner Retainer Grommet
p/n: 70-1713-88
Grommet, headliner bow end. Twelve (12) required per car.Length: 1.4375 inches.
Headliner Seal
p/n: 20-0573-88
Headliner Seal - One hundred seventy six (176) inches long to hold Headliner - Goes Around The Interior Perimeter Of Cab.
Heater control valve seal
p/n: 50-0356-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
Heater control valve seal
p/n: 50-0347-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water.
Hinge Pillar Weatherstrip
p/n: 20-3092-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hinge Seal Set
p/n: 60-0285-69
Seal, back door hinge, outside. A four (4) piece set. Some vehicles require two (2) sets.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.