Weatherstrip, front door kit. Includes weatherstrip for door perimeter and hinge pillar.
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This windshield gasket set contains the windshield gasket itself and the locking strip. The seal mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This rear window gasket set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Weatherstrip, lower door hinge pillar. Attaches to body on hinge pillar. Molded without metal core.Length: 36.0 inches.
Engine support, front. Revulcanization service only.
Support, engine mount at rear. Revulcanization service only.
Pad, accelerator pedal. Revulcanization service only.
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
Weatherstrip windwing lower front corner, right and left.Length: 3.75 inches.
Weatherstrip, rear quarter window leading edge against door glass frame, right and left.Length: 13.50 inches. Width: .8125 inches.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Weatherstrip, hood to cowl. Fully molded with carrot-bumper retainers.Width: .625 inches.
Weatherstrip, front door, right and left, lock side on door upper corner. Designed to attach to our #70-0219-73 weatherstrip.Length: 3.25 inches.
Grommet, steering column at floorboard.Length: 4.50 inches.
Cover, power brake pedal, with "Easamatic power brake" logo. Fully molded with script just like original.
Bumper, upper division post for hardtops and convertibles.
Bumper, front spring rebound, upper.Height: 2.25 inches.
Run channel, front door window, lock side below beltline.
Retainer, intermediate bearing. All models with two piece driveshafts.
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber. One and nine sixteenths inch (1 9/16") length by one and nine sixteenths inch (1 9/16") width by three fourths inch (3/4") inside hole diameter by one and elev
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Seal, rear shield to bumper.Length: 84.0 inches. Width: .75 inches.
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber. One and one half inch (1 1/2") length by one and one eighth inch (1 1/8") width by three fourths inch (3/4") inside hole diameter by one and one half inch (1 1/2") hei
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
Weatherstrip, windshield stanchion, on upper body pillar. Correct extrusion cut seventeen (17) inches long.
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Grommet, heater core at firewall.Length: 3.5625 inches. Width: 2.25 inches.
Grommet, handbrake rod to dash.Height: 1.875 inches.
Grommet, wiring harness.
Boot, gearshift on steering column. Brown rubber. For black see our #30-0069-36. Two and one eighth (2-1/8) inch long style.
Pad, rear spring insulator. Order four (4) per car.Length: 4.75 inches. Width: 2.875 inches.
Boot, gearshift on steering column. Black rubber. For brown see our #30-0069-89. Two and one eighth (2-1/8) inch long style.Length: 2.25 inches.
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Pad, fender mounted antenna.Length: 2.5 inches.
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Grommet, accelerator pedal hinge to floorboard.Length: 3.50 inches. Width: 2.50 inches.
Bumper, hood, on side of fender. Six (6) required per car.Length: 1.0 inches. Width: 1.375 inches.
Grommet, antenna mounting. Fits all models with power antenna. Used with our #70-0756-19.
Insulator, rear spring leaf clip. Seven and one half (7-1/2) inch long, customer may trim for shorter lengths. May use up to eight (8) per car.
Grommet, accelerator pedal rod through floorboard.
Grommet, dimmer switch for carpet application.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Knob, inside door lock control, flexible rubber, black only.Height: 1.125 inches.
Grommet, headlight dimmer switch through floorboard.
Pad, body mounting. Fully molded rubber. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one eighth inch (2 1/8") outside diameter by three fourths inch (3/4") inside hole diameter by five sixteenths inch (5/16") he
Dust cover, tie rod ends.