This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This kit includes the weatherstrip components needed for the glass on your restoration project.
This Convertible Roof Rail Weatherstrip Set fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
This Front Door Vent Window Set is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This Front Door Vent Window Weatherstrips contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
This Revulcanization Service Only is designed to restore your Front Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners. It also has the slot to accommodate the outer edge's decorative molding.
Door edge weatherstrip with molded ends. This part is the primary door to body weatherstrip. Includes eight (8) clips for easy installation. Made of top quality rubber.
Engine harmonic balancer. Revulcanization service only. Send in your old, rebuildable balancer and pulley assembly.
Weatherstrip, front door opening, auxiliary on cowl at beltline. Right and left, brass core.
This eight (8) piece Taillight Lens Gasket set is designed from the original part for superior fitment and seal. The set includes steel rule die-cut and molded rubber gaskets for the taillight lens and body mounting to fender.
This two (2) piece kit includes the gas tank filler neck upper and lower collar seals. These seals prevent gas fumes from entering the cabin. The upper seal fits on top of the fuel neck and seals against the back side of the fender behind the taillight. The collar seals the neck where it goes through rear fender splash panel on the trunk floor.
This 1948-1959 Cadillac Master Parts List - Two (2) Volume set licensed Detroit Iron reprint provides the most comprehensive repair information in paper format. This OEM PARTS manual reproduction provides detailed original part numbers, part assembly diagrams / illustrations and part textual details for all vehicle subsystems.
This Revulcanization Service Only is designed to restore your Rear Engine Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Pad, air conditioning air intake (scoop) mounting.Length: 6.375 inches.
Bumpers, front spring. Lower arm, original copy, integral molded plate and stud, three eighths (3/8) inch standard thread, for installing.
This Gas Tank Filler Upper Seal fits on top of the fuel neck and seals against the back side of the fender behind the taillight. A premium part fully molded with high quality EPDM rubber.
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Seal, rear bumper to body. Includes two (2) thirty (30) inch strips of extrusion.Length: 30.0 inches. Width: 2.4375 inches.
Fender Skirt Edge Seal pair. Length: 60.0 inches. Width: 5/8 inches.
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Seal, headlight to front fender retainer seal. Fully molded to fit like original, unlike a extruded strip that will buckle.
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
These quarter window fillers mount inside the rear panel at the bottom of the rear side window. The pair is fully molded as left and right with brass cores.
Weatherstrip, front door auxiliary, on door at beltline, right and left. Uses snap-in fasteners, four (4) each included.
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Grommet, air conditioning pipes to compressor and condenser. One (1) per car.Length: 4.375 inches. Width: 2.5 inches.
Bumper, side window glass in vent frame at top, right and left, brass core.Length: 1.625 inches.
Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar. Available in 15" pairs.
This Beltline Weatherstrip is sold as a three (3) foot pair. The beltline is used for side window inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Grommet, steering column at floor, fits chrome ring.
Gasket, fog light lens.Length: 8.5 inches. Width: 4.125 inches. Height: .125 inches.
This two (2) piece A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms only.
Headlight body mounting gasket. Rubber.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Insulator, steering column lower mounting frame gasket. Triangular shape with mounting holes and column tube clearance.
Grommet, used for windshield washer, vacuum lines, antenna lead, and others through firewall.
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining. Available in 15" pairs.