Search Results
Please click on the part name in red in order to get a complete description.
Glass Weatherstrip Kit
p/n: 90-3050-90
This kit includes the weatherstrip components needed for the glass on your restoration project.
Body Weatherstrip Kit
p/n: 90-3059-90
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Side window run channel kit
p/n: 90-0141-58
This ten (10) piece kit includes the inner and outer windowfelts, upper and lower rigid run channels, and flexible run channels needed to complete two (2) doors. Used for front or rear doors in models with vent windows in the door.
Front Door weatherstrip
p/n: 70-0664-72
Door edge weatherstrip. This part is the primary door to body weatherstrip. Sufficient for two doors. Adhesive not included in kit.
Rear Door weatherstrip
p/n: 70-0676-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Motor mount service
p/n: 70-0698-11
Cushion, motor support, front. Two (2) per car. Revulcanization service only.
Front Door Vent Window Kit
p/n: 90-0427-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 50-0214-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 70-0596-81
This rear window gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Harmonic balancer service
p/n: 70-1047-12
Engine harmonic balancer. Revulcanization service only. Send in your old, rebuildable balancer and pulley assembly.
Front Door Vent Window Weatherstrips
p/n: 38-0093-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Door weatherstrip
p/n: 70-0544-73
Weatherstrip, front door opening, auxiliary on cowl at beltline. Right and left, brass core.
Taillight lens gasket kit
p/n: 70-0876-15
Gasket set, taillight lens and body mounting to fender. Steel rule die cut and molded rubber.
Gas Filler Neck Seal Kit
p/n: 70-3763-39
This two (2) piece kit includes the gas tank filler neck upper and lower collar seals. These seals prevent gas fumes from entering the cabin. The upper seal fits on top of the fuel neck and seals against the back side of the fender behind the taillight. The collar seals the neck where it goes through rear fender splash panel on the trunk floor.
Motor mount service
p/n: 70-0629-11
Cushion support, motor, rear on transmission to cross member. Revulcanization service only. Similar to #70-0674-11.Length: 3.75 inches. Width: 2.25 inches.
Motor mount service
p/n: 70-0674-11
Cushion, motor support, rear on transmission to cross member. Revulcanization service only.
Trunk Weatherstrip
p/n: 70-0896-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Air intake scoop mounting pad
p/n: 70-2022-31
Pad, air conditioning air intake (scoop) mounting.Length: 6.375 inches.
Front spring bumper
p/n: 70-0172-32
Bumpers, front spring. Lower arm, original copy, integral molded plate and stud, three eighths (3/8) inch standard thread, for installing.
Rigid run channel
p/n: 70-0536-58
Run channel, front door window, for full length of division bar (approximately twenty nine (29) inches). Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top.
Gas Tank Filler Upper Seal
p/n: 70-3701-39
This Gas Tank Filler Upper Seal fits on top of the fuel neck and seals against the back side of the fender behind the taillight. A premium part fully molded with high quality EPDM rubber.
Upper suspension arm dust seal
p/n: 70-0890-32
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Rear bumper seal
p/n: 70-1830-45
Seal, rear bumper to body. Includes two (2) thirty (30) inch strips of extrusion.Length: 30.0 inches. Width: 2.4375 inches.
Fenderskirt edge seal
p/n: 70-0897-44
Seal, fender skirt edge.Length: 60.0 inches. Width: .625 inches.
Axle rebound pad
p/n: 70-0210-32
Bottoming pads, rear axle. Rubber block mounts by bracket to rear axle tube.
Stabilizer bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Fenderskirt Edge Seal
p/n: 70-0154-45
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Headlight seal
p/n: 70-2574-14
Seal, headlight to front fender retainer seal. Fully molded to fit like original, unlike a extruded strip that will buckle.
Hood To Cowl Weatherstrip
p/n: 70-0940-42
Weatherstrip, hood to cowl. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay directly to the body.
Door weatherstrip
p/n: 70-0551-73
Weatherstrip, front door auxiliary, on door at beltline, right and left. Uses snap-in fasteners, four (4) each included.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Body Anti-Squeak Rubber
p/n: 60-0054-73
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
Fuel Filler Neck Lower Cover Collar Seal
p/n: 70-3700-39
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Air conditioning pipe grommet
p/n: 70-0934-31
Grommet, air conditioning pipes to compressor and condenser. One (1) per car.Length: 4.375 inches. Width: 2.5 inches.
Rigid Run Channel
p/n: 70-0347-58
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Front Stabilizer Bar End Link Kit
p/n: 70-2108-33
Kit, front stabilizer bar link assembly replacement. Twenty-two (22) piece set. Set for both sides of one car. Hex head bolt. 5/16"-24nf x 6-9/16" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Flexible Run Channel 6 Foot
p/n: 70-1239-58
Window run channel with stainless beaded edge. Six (6) foot length. Cloth covered, mohair lined, flexible channel for sides and top of door windows. Exact replacement for listed vehicles but can be used in many applications.
Beltline weatherstrip
p/n: 70-0555-58
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Headlight Door To Lens Seal
p/n: 70-0389-14
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Vent division bar weatherstrip
p/n: 70-0868-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Fog light lens gasket
p/n: 70-1033-17
Gasket, fog light lens.Length: 8.5 inches. Width: 4.125 inches. Height: .125 inches.
Flexible Run Channel 5 Foot
p/n: 70-1238-58
Window run channel, stainless beaded edge. Cloth covered, mohair lined flexible metal channel for sides and top of door windows. Perfect dimensions, Five eighths (5/8) inch wide by nine sixteenths (9/16) inch overall height, exact replacement. Five (5) fo
Splash apron
p/n: 70-2772-45
Filler, splash apron. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Steel sash channel
p/n: 70-0641-58
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Steering column gasket
p/n: 70-2317-88
Insulator, steering column lower mounting frame gasket. Triangular shape with mounting holes and column tube clearance.
Firewall grommet
p/n: 70-0967-20
Grommet, used for windshield washer, vacuum lines, antenna lead, and others through firewall.
Rigid run channel
p/n: 70-0516-58
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Steering column finish strip
p/n: 70-1707-88
Seal, steering column to instrument panel. Extruded rubber strip thirteen (13) inch to exact cross-section.Length: 13.0 inches. Width: .625 inches.
Firewall grommet
p/n: 70-0984-20
Grommet, firewall wiring harness. Three and one eighth (3-1/8") long and two and one sixteenth (2-1/16") wide/Length: 3.125 inches. Width: 2.0625 inches.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Brake pedal pad
p/n: 70-1095-22
Pad, brake pedal. Fully molded duplicate of original pattern.Length: 3.75 inches. Width: 2.4375 inches.
Gas filler dust shield
p/n: 70-3773-41
Dust shield, gas filler. Die cut masticated rubber to authentic original dimensions.
Rear bumper end fillers
p/n: 70-3774-30
Seals, rear bumper end filler. Die cut masticated rubber to authentic original dimensions.
Rear spring pad
p/n: 70-0980-32
Pad, rear spring insulator. Two and one half (2-1/2) inches wide, with cloth reinforcement. Used upper and lower on spring. Four (4) used per car.
Metal sleeved grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Trunk bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Firewall grommet
p/n: 70-1040-20
Grommet, air conditioning Freon lines to chassis. Up to six (6) required per car.Length: 1.75 inches. Width: .84375 inches.
Window stop stem bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required. (See sketch and our #33-0540-62).
Solenoid plunger boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Lower suspension arm dust seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Parking/Backup light lens gasket
p/n: 70-1272-16
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body mounting pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body mounting pad
p/n: 70-2234-48
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Window stop stem bumper
p/n: 33-0622-62
Bumper, window stop. One and one fourth (1-1/4) inch square by one half (1/2) inch thick. Compare with our #33-0540-62 and #33-0675-62.Length: 1.
Hood bumper
p/n: 70-0935-42
Bumper assembly, seven eighths (7/8) inch diameter by three eighths (3/8) inch bumper on 1/4-20 stud.Height: 1.50 inches.
Instrument panel grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Shift lever bushing
p/n: 70-2026-26
Bushing, lower shift levers and adjustable eye. Includes metal tube bearing. Used on transmission shifter rods.
Window stop stem bumper
p/n: 33-0540-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Trunk Weatherstrip
p/n: 70-0650-85
This weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be applied to the body of the car.
Door bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door Weatherstrip w/ Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1112-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Brown door lock knob
p/n: 70-0660-70
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Run channel mohair liner
p/n: 70-2863-58
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
Lock cylinder gasket
p/n: 70-0955-86
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.Length: 1.75 inches. Width: 1.25 inches. Height: .
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Body hole plug
p/n: 35-0863-45
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Channel filler weatherstrip
p/n: 70-0489-58
Weatherstrip, channel filler, door window sash channel and some quarter window sash channel. Special type with wide weatherstrip edge to be trimmed at assembly, when necessary.
Door drain hole seal
p/n: 60-0442-70
Weatherstrip, door bottom drain hole seal. Also used on tailgate of station wagon. (Two (2) required for this use).Length: 4.0 inches.
Door Weatherstrip w/o Clips (Sponge Rubber Extrusion - General Use)
p/n: 70-1111-73
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
Door edge weatherstrip made from high quality EPDM sponge rubber. 3M Peel-N-Stick backing provides superior adhesion for reliable performance. Makes for an easier installation of door weatherstripping. Also excellent for use in many different applications and on many different vehicle models.
Stabilizer or shock grommet
p/n: 70-0737-33
Grommet, front stabilizer link or shock absorber. Fully molded rubber. One and one eighths inch (1 1/8") by three eighths inch (3/8") inside hole diameter by seven eighths inch (7/8") height. Use as a front stablizer link for 1946-1970 Cadillac: All mode