Eight (8) piece set. Set includes run channel and beltline weatherstrip.
Door weatherstrip kit. This kit is the primary seal for the door to the body. Set includes the door bottom and perimeter seals that attach to the body and the door edge weatherstrip that attaches to the door.
This front door vent window weatherstrip set is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit. The division post seals contain a brass core for durability and easy installation.
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Made from Standard material. Side window horizontal seal (also known as beltline weatherstrip). These strips wipe the side windows when the glass is lowered. They come ready to install with finished ends and body curvature bends for a factory like appeara
Weatherstrip, interior door edge, black rubber only. (For door bottom, see our #60-0078-73). Two 10 foot strips, enough for two (2) doors.Length: 120.
Grommet, steering gear. Molded with metal core as original with all original features.Length: 4.375 inches.
Channel, rigid division bar. Un-beaded, cloth covered, mohair lined. Perfect replacement requires drilling for screws.
Bumper, axle to frame, rear.
This rear window gasket weatherstrip set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Boot, parking brake lever at floor.
Cushion, overload spring bumper. Fully molded rubber part that installs in overload spring arm.
Headlight Door To Lens Seal - Molded without wire. Double lip type for sealed beam headlights. Note: Compare with our single lip type #70-0389-14 sold separately.
Inner Fender Seal for anti-rattle, runningboard apron to body, or fender splash panels. Nine sixteenths (9/16) inch by seven eighths (7/8) inch slotted sponge rubber to accept rivets. Sold in eight (8) foot strips.
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair and 6ft piece.
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft and 6ft lengths.
Pad, accelerator pedal. Slipover cover type. Exact copy. Fits original steel core.Length: 8.0 inches.
Headlight body mounting gasket. Rubber.
Gasket, cowl vent. Labyrinth type as original.Length: 16.75 inches.
Grommet, fuel filler neck (1955-2nd type). Fully molded rubber, slightly oblong. Three and one half inch (3 1/2") outside width by three and fiftteen sixteenths inch (3 15/16") outside length by two and one eighth inch (2 1/8") inside hole diameter by one
Pad, brake and clutch pedal.Length: 3.5 inches. Width: 2.5 inches.
Weatherstrip, door bottom. Retained by metal strip, black only. Each strip approximately thirty two and one half (32-1/2) inches long.
Grommet, fuel filler neck. Oblong shaped molded rubber with retaining flange. Three and three fourths inch (3 3/4") outside length by three and five eighths inch (3 5/8") outside width. Two and thirteen sixteenths inch (2 3/16") inside hole width by two
Weatherstrip, door window at beltline, outer, (scraper type). Each strip approximately twenty six (26) inches to twenty seven (27) inches long.
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Seal, vertical, front quarter panel (fender) to cab at rear of fender (cowl). Two (2) piece set for both sides of cab.Length: 36.0 inches. Width: .
Boot, brake master cylinder rod. Fits on one and one fourth (1-1/4) inch diameter cylinder. Height: 2.125 inches.
Pad, brake and clutch pedal. Length: 3.75 inches. Width: 2.375 inches.
Bumper, brake or clutch pedal to floorboard. Longer type with one and three eighths (1-3/8) inch clearance for pedal shaft.Length: 2.75 inches.
Weatherstrip, lower door. Heavy type with original ribbing and retainer lip.
Grommet, firewall, throttle rod and tube, oil pressure gauge pipe, heat indicator tube and choke rod. One and seven sixteenths (1-7/16) inch outside diameter.
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Hose, cowl vent drain.Length: 7.25 inches.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Grommet, wiring harness through firewall, for one and one fourth (1-1/4) inch hole in sheet metal.Height: .75 inches.
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Bushing, for shock absorber link cross pin or stabilizer link cross pin.1931-36 Bushing, rubber, for shock absorber link cross pin, #41151.
Seal, steering column at toe pan, sponge.Length: 5.375 inches. Height: .25 inches.
Bushing, gearshift shaft lever, larger type. Three eighths (3/8) inch inside diameter by nine sixteenths (9/16) inch outside diameter barrel.Height: .
Grommet, electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fits seven eighths (7/8) inch hole in light body. Two (2) to eight (8) per car as required.
Bushing, rear spring, shackle eye and spring eye. Up to twelve (12) per car.CV/GMC TRK 1955-57 Bushing, rubber, rear spring, shackle eye and spring eye.
Gasket, taillight to fender. Two 1/4" strips of sponge rubber cut 26-3/4" long. One (1) pair required per car.
Bushing, body shackles.Length: 1.125 inches.
Bumper, hood side upper. Fully molded, authentic configuration for 1/4" hole. Six (6) typically required per vehicle. Note: This part is included in our 90-0213-90 Body Bumper
Bushing, shock absorber arm link.
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available. Available by the foot.
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Grommet, shock absorber mounting, plain cylinder type with flat ends.