This four (4) piece Front Door Vent Window Set contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This is a six (6) piece door edge weatherstrip set. With three (3) parts for each door, this part is the primary door to body weatherstrip. Includes our part #20-3122-73.
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This roof rail weatherstrip pair is made of high-quality EPDM rubber with vulcanized corners for a factory like fit. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
This Windshield Gasket is designed from the original part for superior fitment and seal. This gasket has a slot only on the bottom of the seal to accommodate the outer edge's decorative molding.
This three (3) piece Upper Control Arm Shaft set is designed from the original part for superior fitment and performance. Renew the performance of your aged and worn front suspension to restore the ride of your classic vintage vehicle.
Seals, top rear of door. Not included in door seal kits.
Seal assembly. Installs on body below rear quarter glass to body weatherstrip.
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
This Front Engine Mount is made of a quality rubber over a metal core to provide maximum life and performance. Two (2) required per car.
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This channel is for the Left Front Door.
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This channel is for the Right Front Door.
This Beltline Weatherstrip installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
This Radiator Splash Shield set is designed from the original part for superior fitment and seal. Set of 4.
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
This two (2) piece Splash Apron is designed from the original part for superior fitment and seal. This pair attaches to the inner fender to suspension arm.
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
This six (6) piece Splash Apron set is designed from the original part for superior fitment and seal. Installs on fender splash apron and bottom of radiator side deflectors.
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.
This Clutch Rod to Firewall Boot is designed from the original part for superior fitment and seal. This boot makes a weathertight connection for the clutch rod lever as it passes through the firewall.
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Pads, taillight to body.
Support, transmission. Models with manual transmission only.
Bushing, brake master cylinder. Installs on push rod.
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Bumper, front suspension lower. Left side.
Bumper, front suspension lower. Right side.
Grommet, fuel filler neck. Fully molded rubber.
Pad, rear spring. Upper and lower. Four (4) required per car.
Gaskets, back-up light cover. Used on models without back-up lights.
Seal, steering tube to floor. Installs under floor mat.
This Windshield Post To Door Weatherstrip pair is designed from the original part for superior fitment and seal. These weatherstrips attache to the body and seal between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Seal, radiator air deflector to hood. Twenty two and one fourth (22-1/4) inches long. Two (2) piece set.
Rubber, garnish molding to dash. Eighty two (82) inches long.
Bushing, Rear Spring - Front #B5A-5781-C
Insulator, transmission gear shift column lever.
Seal, steering column tube. Installs on top of floor mat.
Bushing, control arm. Two (2) required per side.
This Splash Apron mounts between the front fender splash apron and the front fender. The seal is an exact reproduction of the original Ford part. Sold as a seventy-two (72) inch strip.
Bushings, stabilizer bar to frame. One (1) pair required per car.
Gaskets, ventilator air valve.1952-54: 1 pair required. 1955-56: 2 pair required.
Pad, rear mount antenna.
Gaskets, back-up light housing to body.
Bushing, control arm. Upper inner rear. One (1) required per side.