Door edge weatherstrip. This part is the primary door to body weatherstrip.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Kit, upper shaft front suspension.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pair.
Weatherstrip, door window inner and outer, front and rear doors. Bend to fit. Available in a 3ft pair.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Pads, radiator splash shield. Four (4) required per vehicle.
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Four (4) piece kit includes inner and outer felt beltline weatherstrip for each door and quarter windows.
Seals, front fender inner splash apron to suspension arm.
Bumper kit, hood. Ten (10) piece set.
Seal, fender skirt.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
This Clutch Rod to Firewall Boot is designed from the original part for superior fitment and seal. This boot makes a weathertight connection for the clutch rod lever as it passes through the firewall.
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Repair kit, stabilizer bar end. Eleven (11) piece set. Two (2) kits required per car. Hex head bolt. 3/8"-24nf x 5-7/16" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Pads, taillight to body.
Support, transmission. Models with manual transmission only.
Seals, dash bezel. Five (5) piece set.
Bushing, brake master cylinder. Installs on push rod.
Pads, parking light body to fender.
Bolt and bushing kit, rear of rear spring shackle. Enough for one (1) side only.
Bumper, front suspension lower. Left side.
Bumper, front suspension lower. Right side.
Grommet, fuel filler neck. Fully molded rubber.
Pad, rear spring. Upper and lower. Four (4) required per car.
Gaskets, back-up light cover. Used on models without back-up lights.
Seal, steering tube to floor. Installs under floor mat.
Seal, radiator air deflector to hood. Twenty two and one fourth (22-1/4) inches long. Two (2) piece set.
Rubber, garnish molding to dash. Eighty two (82) inches long.
Bushing, Rear Spring - Front #B5A-5781-C
Insulator, transmission gear shift column lever.
Set, spring clamp liner. Front spring takes eight pieces for both sides Rear spring takes four pieces for both sides. Six (6) piece set.
Bushing, control arm. Two (2) required per side.
Bushings, stabilizer bar to frame. One (1) pair required per car.
Gaskets, ventilator air valve.1952-54: 1 pair required. 1955-56: 2 pair required.
Pads, outside door handle. Four (4) piece set.
Pad, rear mount antenna.
Gaskets, back-up light housing to body.
Bushing, control arm. Upper inner rear. One (1) required per side.
Bushing, control arm. Upper inner front. One (1) required per side.
Seal, front of door. Goes up windshield post.
Grommet, fuel filler neck. Fully molded flexible rubber. Four inch (4") outside diameter by two and one eighth inch (2-1/8") inside diameter by one half inch (1/2") height.
Kit, hood to cowl weatherstrip. Forty-one inch (41") extruded rubber strip includes installation tacks.
Seal, rear stone deflector. Installs between body and rear bumper.
Weatherstrip, window sash channel. Thirty six (36) inch long roll. One (1) required per window.Length: 36.0 inches.
Pads, outside door handle. Pair does two (2) doors.