Search Results
Please click on the part name in red in order to get a complete description.
Front Door Weatherstrip
p/n: 90-0146-72
Weatherstrip, front door kit. Includes weatherstrip for door perimeter and hinge pillars. Set includes our #30-0504-73, #30-0326-73, and #30-0417-73.
Vibration damper service
p/n: 30-0520-12
Vibration damper, crankshaft, front. Revulcanizing service only. NOTE: This service does not include rebalancing.
Windshield Gasket
p/n: 30-0270-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket Set
p/n: 30-0463-81
This rear window gasket set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Door weatherstrip
p/n: 90-0147-72
Weatherstrip, rear door kit. Includes weatherstrip for door perimeter and hinge pillars.
Front Door Vent Window Kit
p/n: 90-0316-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Motor mount service
p/n: 30-0378-11
Insulator assembly, engine support, front. Revulcanizing service only.
Rear Door Vent Window Weatherstrip
p/n: 30-0481-74
This rear door vent window weatherstrips pair is designed from the original parts for superior fitment and seal.
Door weatherstrip
p/n: 30-0326-73
Weatherstrip, front doors, right and left, on hinge pillar below beltline. This is a vertical weatherstrip mounted on the body.Length: 33.25 inches.
Rear Door hinge pillar seal
p/n: 30-0496-73
Weatherstrip, rear door hinge pillar. Attaches to body on hinge pillar. Molded without metal core.
Front Door Vent Window Weatherstrips
p/n: 70-1510-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Motor mount service
p/n: 30-0424-11
Mount, engine support, rear. Revulcanization service only. For all models with UltraMatic transmission.
Front suspension bumper
p/n: 70-1295-32
Bumper assembly, front load compression, lower.Width: 2.125 inches. Height: 2.75 inches.
Front spring bumper
p/n: 30-0517-32
Bumper, front spring rebound, lower.Width: 2.125 inches. Height: 2.25 inches.
Trunk Weatherstrip
p/n: 70-1691-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Division bar grommet
p/n: 70-3132-62
Grommets, rear door vent divider post, upper and lower, right and left. 4 piece set.
Rigid run channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Power brake pedal pad
p/n: 70-2411-22
Cover, power brake pedal, with "Easamatic power brake" logo. Fully molded with script just like original.
Axle rebound pad
p/n: 70-1290-32
Bushing, rear support arm. Rear lower. Four (4) per car. For upper see #70-1289-32.
Axle rebound pad
p/n: 70-1289-32
Bushing, rear support arm. Rear upper. Four (4) per car. For lower see #70-1290-32.
Front suspension bumper
p/n: 70-1294-32
Bumper, front load rebound, upper.Width: 1.625 inches. Height: 2.75 inches.
Axle rebound pad
p/n: 30-0534-32
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
Carpet heel plate
p/n: 70-3019-88
Heel pad for carpet. Seven and three eighths (7-3/8) inch wide by sixteen (16) inches long.
Front stabilizer bushing
p/n: 70-1293-33
Bushing, front stabilizer rod. One (1) pair per vehicleLength: 1.5625 inches. Width: 1.75 inches. Height: 1.625 inches.
Vent division bar weatherstrip
p/n: 70-1511-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Gravel shield anti-squeak
p/n: 30-0476-44
Seal, rear shield to bumper.Length: 84.0 inches. Width: .75 inches.
Vent Window Division Bar Weatherstrip
p/n: 30-0541-74
Division post seal pair for rear door vent window. Made from top quality rubber to ensure durability and proper seal. Designed from original part so it fits correctly.
Beltline weatherstrip
p/n: 30-0300-58
Window felt inner and/or outer. One (1) pair of three (3) foot lengths. Flexible, pile lined, rubber covered, with stainless bead. For front door, rear door and quarter windows. Replaces factory #466634, 466635.
Coil wire sleeve
p/n: 70-2052-21
Boot, spark plug wire, at spark plug. All original textures and details.Length: 2.0 inches.
Front stabilizer bushing
p/n: 30-0298-33
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber. One and one half inch (1 1/2") length by one and one eighth inch (1 1/8") width by three fourths inch (3/4") inside hole diameter by one and one half inch (1 1/2") hei
Windshield weatherstrip
p/n: 70-1535-52
Weatherstrip, windshield garnish molding on lower windshield post. Molded rubber replacement for #469222-3.
Hood to cowl weatherstrip
p/n: 30-0527-42
Weatherstrip, hood to cowl. Overall thirty seven (37) inches long.
Firewall grommet
p/n: 30-0456-20
Grommet, heater core at firewall.Length: 3.5625 inches. Width: 2.25 inches.
Power window switch bezel pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Firewall seal
p/n: 70-1599-36
Grommet, power steering lines to air duct.Length: 3.3125 inches. Width: .75 inches.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Body mounting pad
p/n: 30-0501-48
Pad, body mounting. Fully molded rubber with metal core. Number used varied according to body type. Two inch (2") outside diameter by three fourths inch (3/4") inside top hole diameter by one half inch (1/2") bottom hole diameter by three fourths inch (3/
Firewall seal
p/n: 70-1600-36
Grommet, power steering lines to frame.Length: 2.75 inches. Height: .75 inches.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Body mounting pad
p/n: 30-0500-48
Pad, body mounting. Fully molded rubber with locating collar and metal core. Number used varied according to body type. Two inch (2") outside diameter by one inch (1") locating collar outside diameter by three fourths inch (3/4") inside locating collar ho
Body mounting pad
p/n: 70-1429-48
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Battery clamp cover
p/n: 70-0095-21
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Accelerator hinge grommet
p/n: 30-0539-41
Grommet, accelerator pedal hinge to floorboard.Length: 3.50 inches. Width: 2.50 inches.
Hood bumper
p/n: 30-0304-42
Bumper, hood, on side of fender. Six (6) required per car.Length: 1.0 inches. Width: 1.375 inches.
Heater core tube grommet
p/n: 30-0421-31
Grommet, heater inlet and outlet hose. Soft pliable rubber.
Power steering bushing
p/n: 70-1968-36
Bushing, power steering cylinder to frame. Two (2) required per car.Height: .625 inches.
Masticated rubber sheet
p/n: 70-0645-45
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Body mounting pad
p/n: 50-0097-48
Pad, several useages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car. Two inches (2") outside diameter by three fourths inch (3/4") inside hole diameter by one half inch (1/2") he
Body mounting pad
p/n: 70-1430-48
Pad, body mounting. Fully molded rubber. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one eighth inch (2 1/8") outside diameter by three fourths inch (3/4") inside hole diameter by five sixteenths inch (5/16") he
Headliner retainer grommet
p/n: 70-1713-88
Grommet, headliner bow end. Twelve (12) required per car.Length: 1.4375 inches.
Overdrive linkage grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Door Weatherstrip
p/n: 70-0491-73
Weatherstrip, door edge. Fine grain sponge. Larger type used on most GM cars this period. Width: 13/16". Height: 11/16".
Trunk Weatherstrip (Sponge Rubber Extrusion - General Use)
p/n: 30-0356-85
Trunk weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Universal mounting pad
p/n: 70-0308-17
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Door weatherstrip
p/n: 70-0219-73
Weatherstrip, door edge, constant section on some models. Five eighths (5/8) inch by (5/8) inch cross-section, high grade, fine grain sponge rubber.
Sash channel filler 1/16 cork
p/n: 70-1115-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Antenna grommet
p/n: 32-0390-21
Grommet, insulator. For rear mounted twin antennas. Sheet Metal Hole: 1" Center Hole: 3/4" Outside Diameter: 1-1/4" Slot Width: 1/16"
Hood bumper
p/n: 33-0542-42
Pad, hood side to fender. Button type, fits five sixteenths (5/16) inch hole, self retaining.
Sash Channel Filler 1/16 Rubber
p/n: 70-2170-57
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Sash channel filler 1/32 cork
p/n: 70-1114-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality linen back, rubber cork composition
Sash Channel Filler 1/32 Rubber
p/n: 70-2169-57
Filler strip, window glass sash channel. One thirty seconds (1/32) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler.
Shock absorber bushing
p/n: 70-0547-32
Bushing, shock absorber mounting. Double cone style, rear. Five eighths (5/8) inch hole, one and one sixteenths (1-3/16) inch outside diameter, three fourth (3/4) inch thick.
