Please click on the part name in red in order to get a complete description.
This kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
This kit includes the weatherstrip components needed for the glass on your restoration project.
Hardtop roof rail weatherstrip, with metal core. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
This front door vent window weatherstrip kit is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
This front door vent window weatherstrip set contains the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Cushion, motor support, front. Two (2) per car. Revulcanization service only.
Door edge weatherstrip. This part is the primary door to body weatherstrip.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Door edge weatherstrip. This part is the primary door to body weatherstrip. Includes six (6) clips for easy installation.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Engine harmonic balancer. Revulcanization service only. Send in your old, rebuildable balancer and pulley assembly.
Weatherstrip, front door opening, auxiliary on cowl at beltline. Right and left, brass core.
Gasket set, taillight lens and body mounting to fender. Steel rule die cut and molded rubber.
Cushion, motor support, rear on transmission to cross member. Revulcanization service only.
Cushion support, motor, rear on transmission to cross member. Revulcanization service only. Similar to #70-0674-11.Length: 3.75 inches. Width: 2.25 inches.
This two (2) piece kit includes the gas tank filler neck upper and lower collar seals. These seals prevent gas fumes from entering the cabin. The upper seal fits on top of the fuel neck and seals against the back side of the fender behind the taillight. The collar seals the neck where it goes through rear fender splash panel on the trunk floor.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Pad, air conditioning air intake (scoop) mounting.Length: 6.375 inches.
Run channel, front door window, for full length of division bar (approximately twenty nine (29) inches). Rigid, bright beaded edge, mohair lined channel, die trimmed and formed at top.
This Gas Tank Filler Upper Seal fits on top of the fuel neck and seals against the back side of the fender behind the taillight. A premium part fully molded with high quality EPDM rubber.
Seal, upper A-arm, inner and outer. Four (4) piece set.Height: 1.0 inches.
Seal, fender skirt edge.Length: 60.0 inches. Width: .625 inches.
Bottoming pads, rear axle. Rubber block mounts by bracket to rear axle tube.
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Grommet, steering column at floor.
Seal, steering column to firewall. For 1956 vehicles purchase our #70-1509-88 grommet separately. For 1957-58 vehicles purchase our #70-2316-88 grommet separately.
Weatherstrip, hardtop roof rail filler or extension. Attaches to body. Made with metal core like originalLength: 4.75 inches. Height: .625 inches.
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Filler, rear bumper to body. Die cut masticated rubber.
Weatherstrip, hood to cowl. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay directly to the body.
Weatherstrip, front door auxiliary, on door at beltline, right and left. Uses snap-in fasteners, four (4) each included.
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
Bulb type seal, gravel shield-to-rear bumper, anti-squeak. Also used as a door weatherstrip for some makes and models. Twelve (12) foot strip.
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Grommet, air conditioning pipes to compressor and condenser. One (1) per car.Length: 4.375 inches. Width: 2.5 inches.
Channel, rigid run, window division bar. Stainless beaded edge, mohair-lined, exact replacement for rear side of division bar.
Kit, front stabilizer bar link assembly replacement. Twenty-two (22) piece set. Set for both sides of one car. Hex head bolt. 5/16"-24nf x 6-9/16" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Weatherstrip, door window inner and outer, front and rear doors. Seven sixteenths (7/16) inch wide, with chrome bead, mohair faced, flexible. Two (2) three (3) foot strips. Bend to fit.
Side window vertical leading edge weatherstrip.
Headlight door to lens seal. Molded without wire. Single lip type for sealed beams.
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Gasket, fog and parking light lens housing.Length: 8.5 inches. Width: 4.0 inches.
Filler, splash apron. Die cut masticated rubber to authentic original dimensions. Includes all factory style holes required for installation.
Headlight body mounting gasket. Rubber.
Sash channel, side window glass. U-shaped steel channel only, no filler. Will require that you attach your own window regulator cam to underside as required.
Grommet, used for windshield washer, vacuum lines, antenna lead, and others through firewall.
Weatherstrip, windshield post, upper to door. Seals between front door vent window frame and windshield pillar. Top quality rubber made to original cross-section. Two (2) strips approximately fifteen (15) inches long. May need to trim ends to fit.
Channel, rigid run, lower side window below beltline, zinc plated steel with black cloth lining, one half (1/2) inch deep by one half (1/2) inch wide, fifteen (15) inches long.
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Seal, steering column to instrument panel. Extruded rubber twelve (12) inch strip to exact cross-section.Length: 10.5 inches. Width: .50 inches.
Grommet, parking brake cable through firewall.Length: 1.75 inches.
Grommet, firewall wiring harness. Three and one eighth (3-1/8") long and two and one sixteenth (2-1/16") wide/Length: 3.125 inches. Width: 2.0625 inches.
Grommet, speedometer cable through firewall.
Gasket, door handle.
Seal, lower suspension arm, inner. Four (4) piece set.
Dust shield, gas filler. Die cut masticated rubber to authentic original dimensions.
Seals, rear bumper end filler. Die cut masticated rubber to authentic original dimensions.
Pad, rear spring insulator. Two and one half (2-1/2) inches wide, with cloth reinforcement. Used upper and lower on spring. Four (4) used per car.
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Cover, battery clamp. Control unsightly sulfate buildup. Help protect the nearby metal and finish. Good copy from original part.Length: 3.5 inches.
Grommet, air conditioning Freon lines to chassis. Up to six (6) required per car.Length: 1.75 inches. Width: .84375 inches.
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Grommet, glove box door cushion. One and three quarters long (1-3/4") and thirteen sixteenths (13/16")wide.Length: 1.75 inches. Width: .8125 inches.
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Grommet, dimmer switch for carpet application.
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Masticated sheet. Three thirty seconds (3/32) inch thick rubber sheet containing random milled cotton cord reinforcement for front end splash aprons, etc. This product is a four (4) foot wide roll, and will only be sold in four (4) square foot multiples
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Bumper, hood side to fender. Four (4) per car.
Bumper, window stop. One and one fourth (1-1/4) inch square by one half (1/2) inch thick. Compare with our #33-0540-62 and #33-0675-62.Length: 1.
Bumper assembly, seven eighths (7/8) inch diameter by three eighths (3/8) inch bumper on 1/4-20 stud.Height: 1.50 inches.
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Spacers, spark plug wires in organizer bracket.
Bushing, spring and shackle, rear.
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Dust cover, tie rod ends.
This weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. The seal is structured to be applied to the body of the car.
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Knob or push button for inside door lock, fits over 1/8" steel rod to door lock. Hard brown rubber, may be lacquered other colors as required.
Liner, mohair. Liner with a rubber backing. Apply with adhesive to division bars and channels. Helps reline guide bars on lock side of hardtops and convertibles.
Gasket, trunk lock cylinder. Steel rule die cut from one thirty seconds (1/32) inch dense rubber.Length: 1.75 inches. Width: 1.25 inches. Height: .
Mounting pad, continuous for lights, hinges, brackets, and other bright work when no molded pad is available.
Plug, body sheet metal holes. Used in various places (like trunks). For one and one half (1-1/2) inch hole in body.
Weatherstrip, door bottom drain hole seal. Also used on tailgate of station wagon. (Two (2) required for this use).Length: 4.0 inches.
Grommet, front stabilizer link or shock absorber. Fully molded rubber. One and one eighths inch (1 1/8") by three eighths inch (3/8") inside hole diameter by seven eighths inch (7/8") height. Use as a front stablizer link for 1946-1970 Cadillac: All mode
Door edge weatherstrip made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models.
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .34 inch high. Use as required four (4) to six (6) per car. For .
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .28 inch high. Use as required four (4) to six (6) per car. For .
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips. Use as required, four (4) to six (6) per car. For .
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherstrip type of filler. This is the highest quality linen back, rubber cork composition on
Retainer, firewall insulation panel. "Christmas Tree" style popular during this time. Constructed of vinyl plastic. Up to ten (10) required per car.
Bumper, door lock post, upper, one half (1/2) inch diameter by one half (1/2) inch tall, plated screw.Height: .50 inches.
Filler strip, window glass sash channel. One sixteenths (1/16) inch thick by 1-1/2 inches wide. For all applications fitting glass to sash channel not requiring weatherlip type of filler. This is the highest quality rubber like polymer designed for settin
Bumper pads, door or tailgate. Twin retainer style. Three eighths (3/8) inch by seven eighths (7/8) inch by one half (1/2) inch high.
Filler and cushion strip, many applications. Five thirty seconds (5/32) inch by one and five eighths (1-5/8) inch.
Bushing, shock absorber mounting. Five eighths (5/8) inch hole, one and one fourth (1-1/4) inch outside diameter, five eighths (5/8) inch thick.