Search Results
Front Door weatherstrip
p/n: 90-0146-72
Weatherstrip, front door kit. Includes weatherstrip for door perimeter and hinge pillars. Set includes our #30-0504-73, #30-0326-73, and #30-0417-73.
Vibration damper service
p/n: 30-0520-12
Vibration damper, crankshaft, front. Revulcanizing service only. NOTE: This service does not include rebalancing.
Windshield Gasket
p/n: 30-0270-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Door weatherstrip
p/n: 90-0147-72
Weatherstrip, rear door kit. Includes weatherstrip for door perimeter and hinge pillars.
Front Door Vent Window Kit
p/n: 90-0316-90
This front door vent window weatherstrip kit is a four (4) piece set that contains the main vent window seals and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Motor mount service
p/n: 30-0378-11
Insulator assembly, engine support, front. Revulcanizing service only.
Rear Door Vent Window Weatherstrip
p/n: 30-0481-74
This rear door vent window weatherstrips pair is designed from the original parts for superior fitment and seal.
Door weatherstrip
p/n: 30-0326-73
Weatherstrip, front doors, right and left, on hinge pillar below beltline. This is a vertical weatherstrip mounted on the body.Length: 33.25 inches.
Rear Door hinge pillar seal
p/n: 30-0496-73
Weatherstrip, rear door hinge pillar. Attaches to body on hinge pillar. Molded without metal core.
Front Door Vent Window Weatherstrips
p/n: 70-1510-55
These front door vent window weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Motor mount service
p/n: 30-0424-11
Mount, engine support, rear. Revulcanization service only. For all models with UltraMatic transmission.
Accelerator pedal service
p/n: 70-3144-41
Pad, accelerator pedal. Revulcanization service only. Includes new ball sockets as original, with correctly detailed tread pattern.
Front suspension bumper
p/n: 70-1295-32
Bumper assembly, front load compression, lower.Width: 2.125 inches. Height: 2.75 inches.
Taillight Gasket Set
p/n: 30-0460-15
This eight (8) piece Taillight Gasket set is designed from the original part for superior fitment and seal. This reproduction set includes all lens and light body gaskets for both sides.
Trunk Weatherstrip
p/n: 70-1691-84
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Division bar grommet
p/n: 70-3132-62
Grommets, rear door vent divider post, upper and lower, right and left. 4 piece set.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Steering column grommet
p/n: 70-1895-36
Grommet, steering column at dash. See #70-1894-36 for grommet at floorboard.Width: 2.625 inches.
Front suspension bumper
p/n: 70-1294-32
Bumper, front load rebound, upper.Width: 1.625 inches. Height: 2.75 inches.
Axle rebound pad
p/n: 30-0534-32
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
Carpet heel plate
p/n: 70-3019-88
Heel pad for carpet. Seven and three eighths (7-3/8) inch wide by sixteen (16) inches long.
Front stabilizer bushing
p/n: 70-1293-33
Bushing, front stabilizer rod. One (1) pair per vehicleLength: 1.5625 inches. Width: 1.75 inches. Height: 1.625 inches.
Vent division bar weatherstrip
p/n: 70-1511-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Window Division Bar Weatherstrip
p/n: 30-0541-74
Division post seal pair for rear door vent window. Made from top quality rubber to ensure durability and proper seal. Designed from original part so it fits correctly.
Beltline Weatherstrip
p/n: 30-0300-58
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with stainless bead. Available in 3ft pair.
Coil wire sleeve
p/n: 70-2052-21
Boot, spark plug wire, at spark plug. All original textures and details.Length: 2.0 inches.
Front stabilizer bushing
p/n: 30-0298-33
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber. One and one half inch (1 1/2") length by one and one eighth inch (1 1/8") width by three fourths inch (3/4") inside hole diameter by one and one half inch (1 1/2") hei
Windshield weatherstrip
p/n: 70-1535-52
Weatherstrip, windshield garnish molding on lower windshield post. Molded rubber replacement for #469222-3.
Hood to cowl weatherstrip
p/n: 30-0527-42
Weatherstrip, hood to cowl. Overall thirty seven (37) inches long.
Firewall grommet
p/n: 30-0456-20
Grommet, heater core at firewall.Length: 3.5625 inches. Width: 2.25 inches.
Parking light gasket
p/n: 70-2023-15
Gasket, parking light housing. Die cut from durable black sponge-cell rubber. One (1) pair needed per car.Length: 11.375 inches.
Antenna mount pad
p/n: 70-2264-21
Pad, antenna mount. For rear mounted twin antennas. See our #32-0390-21 for insulating grommet.
Power window switch bezel pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Firewall seal
p/n: 70-1599-36
Grommet, power steering lines to air duct.Length: 3.3125 inches. Width: .75 inches.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Body mounting pad
p/n: 30-0501-48
Pad, body mounting. Fully molded rubber with metal core. Number used varied according to body type. Two inch (2") outside diameter by three fourths inch (3/4") inside top hole diameter by one half inch (1/2") bottom hole diameter by three fourths inch (3/