Door edge weatherstrip. This part is the primary door to body weatherstrip.
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
This rear window gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding.
Kit, upper shaft front suspension.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Original equipment style side window horizontal seal kit (also known as beltline weatherstrip). Four (4) piece kit includes inner and outer felt beltline weatherstrip for each door and quarter windows.
Seal, fender skirt.
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Repair kit, stabilizer bar end. Eleven (11) piece set. Two (2) kits required per car. Hex head bolt. 3/8"-24nf x 5-7/16" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Seals, dash bezel. Five (5) piece set.
Bushing, brake master cylinder. Installs on push rod.
Seal, cowl side ventilator door. Two (2) required per car.
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.
Bushing, control arm. Upper inner. Two (2) required per side.
Bolt and bushing kit, rear of rear spring shackle. Enough for one (1) side only.
Bumper, front suspension lower. Right side.
Bumper, front suspension lower. Left side.
Insulator, transmission gear shift column lever.
Bushing, control arm. Two (2) required per side.
Bushings, stabilizer bar to frame. One (1) pair required per car.
Pads, taillight to body.
Pads, outside door handle. Four (4) piece set.
Bushing, control arm. Upper inner front. One (1) required per side.
Bushing, control arm. Upper inner rear. One (1) required per side.
Seal, front of door. Goes up windshield post.
Grommet, fuel filler neck. Fully molded flexible rubber. Four inch (4") outside diameter by two and one eighth inch (2-1/8") inside diameter by one half inch (1/2") height.
Weatherstrip, front fender rear splash shield. Staples included.
Pad, rear mount antenna.
Gaskets, parking light lens.
Pads, parking light body to fender.
Kit, cowl lacing. Staples included.
Bumper, front suspension upper.
Liner, rear spring clamp.One (1) set required per car.
Pad, brake and clutch pedal. Slip over type.
Pad, front mount antenna.
Bumper, on lower door and/or fuel filler cover. Type with threaded end.
Insulator, front coil spring.
Gaskets, taillight lens to housing.
Weatherstrip, front fender apron to frame front. Staples included.
Bushing, Rear Spring - Front #B6S-5781-A
Gasket, headlight bucket to fender. Cork.
Grommet, antenna lead-in. For front mount type.
Pads, rear spring anti-squeak. Install between leaves.
Gaskets, wiper pivot bezel to cowl.
Anti-rattler, trunk torsion bar.
Seal, idler arm. Two (2) required per car.
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Grommet, fuel tank vent pipe to body.
Cork sash channel filler. Available by the foot.